Search results

http://www.amazon.com/dp/B000NW9XSK/?tag=atomicindus08-20 I bought this set for my truck and the plastic blow mold case is pretty bad. It can't hold sockets in place at all and I'm not throwing it around or anything I've tried stuffing paper in here in addition to the foam pad but its not...

I guess your method is a little different, I normally work on brake cans a few times a week sometimes more as a fleet tractor trailer mechanic (I'm still new though) I was taught a bit differently As far as supplying air to a 30/30 can off the truck or trailer in order to cut the threaded rod...

What's the diff between using this on fwd hubs and the OTC 9 way slide hammer hub puller pieces ? Sent from my XT1080 using Tapatalk

Why do you say that? Sent from my XT1080 using Tapatalk

Just did my second job with the 1822, amazing !!!!!!!!!!! Sent from my XT1080 using Tapatalk

Or you can just use the cager that comes with all cans Sent from my XT1080 using Tapatalk

Why not just drop the linings, it only takes a minute (literally) Sent from my XT1080 using Tapatalk

There's an m12 and snap on makes one too Sent from my XT1080 using Tapatalk

Can this achieve the same exact working torque as the 1/2? I know most 1/2 and 3/8 paired sets get lower ratings because of anvil size? Sent from my XT1080 using Tapatalk

Test Sent from my XT1080 using Tapatalk

Astro 12sl, most compact rechargable powerful light I could find

Finally got to ordering the onyx 1/2, expected here in a few days..planning on using it at work (tractor trailers) for chassis work like air bag brackets, torque rods, shocks and other suspension components where my mg725 requires awkward angles and swivels with longer extensions or cannot reach...

If I have GW 120 ratchets that need warranty what's the best way to do it? Can I call the company direct? Is it a free lifetime type of deal?

What's wrong with the 120 is it unreliable? I've been thinking about buying the entire 120 set

My stant was very hard to pump, from new.. There's a tiny hole right next to the pump and I just shoot penetrating oil in it, problem solved

My mg325 is an animal, it will snap bolts or pull threads whichever comes first on 1/4 and 5/16 bolts in seconds, it took me a while to learn how to use it without causing damage My mg725 will snap bolts or pull threads on 3/8 and 7/16 bolts also

That bluepoint / kastar ratcheting tool looks like the ultimate piston compressor tool, with a 10 dollar difference I'm just not sure if its worth going generic when you got a guaranteed lifetime warranty with the bluepoint for 10 more... But how prone are they to failure?

Using my new DD 500x for the first time, I realized that in the alignment port there is only one mark - 118* My bits are 135. There are several markings on either side of the 118 (+ and -) The manual says that each marking is 10* The sharpening port only has two presets 118 and 135 So in...

There's a welder on my local CL like this but it's an AC 225 for 300. Thinking about it but I only have a regular house plug and it would be my first welder. Comes with a helmet and rods. Would this be good for me? Or should I go for a brand new Hobart 140 for double the price then I still have...

I bought my snap on cordless through the student program just like you're considering 18v lithium 3/8 impact, 1/2 impact, hammer drill and 7.2v ct661 At this point now that I no longer qualify for the SEP as I'm graduated and out In the work force , I regret not going with the m18 fuel line...