Search results

You are correct-it is a blind hole-as most mfgrs wanted to make it cheaper so they did not have to slot the pin-tap the hole or thread the pin-thus a one step operation thinking that the owner would never have to disassemble, clean, repair said tool! Other than drilling out, or welding a...

Oops-picture attached

Maybe this has been discussed before? Looking for a fairly easy-non destructive method of removal of the pushed-in or pressed-in pins for holding the adjustment screws on adjustable wrenches? Picture attached-thanks any help appreciated........Cranky

Has to be a one of a kind set! Worth megabucks to the right collector!:thumbup:

Never heard of just Fairbanks-there was a company that did sell scales called Fairbanks-Moorse--maybe that this was a socket or set made by a Japanese company for them as a maint. item>Japan made a lot of sockets/tools/sets in the 60-70-80"s for many.????:headscrat

Like new un-used condition other than box rash lines from sliding in drawer. $48.00 delivered to lower 48 address-No date code on this tool. USPS money order or carefully concealed cash @ buyers risk of sending thru mail service. NO ELECTRONIC funds accepted. Thanks for viewing-NO...

Nice catch on the CP compressor-they were originally mfgd. in Franklin, Pa. in the day. Parts might still be available thru the company in N.C./S.C. that bought them out-I've seen where they still make portable construction compressors currently-do a google search and should be able to find...

Looking for RP Combo SAE wrenches with following part numbers 7210 1/4, 7214 7/16, and 7238 1 3/16-were produced in Japan for CP in late 60's-70's. To my knowledge they were all 12 pointers and no Metrics were made or six pointers. Would prefer no POM's/grindings other than factory...

Will just try to shed some light on the machine and previous statements-this machine is a circa 1990 model of which I could be(Unkown) the 3rd-4th-fifth owner! The Type "F" ATF is of the vintage era of which was a hi-detergent grade/viscosity atf which was used in Ford C-6 Trannys for autos...

This machine already was supplied with a 10micron spin-on type filter and requires a filter change @100 hours of usage. Uses type "F" ATF which is NLA as when this machine was mfg. in 1990. The only new synthetic ATF is very expensive @$59.99/gallonx8 gallon capacity! Just trying to save...

Thanks KD: I will check your unit out online-as well as there is a boat load of other drawings etc. to choose from on-line! Just trying to get all opinions b4 pulling the trigger on new or home built unit. Thanks much for your input as well as others!!...........Cranky:thumbup:

I believe the total sump capacity is approximately 8 gallons on this unit and is considered low flow around 14GPM max. rated. The hyd. filter on the unit is 10 micron rated-sort of hard to figure how much flow you would have at the QC's as you also have the seperate 4ea. drive motors for the...

For cleaning the hydraulic fluid on a skid steer-hook up to the quick couplers-turn on and recycle all the fluid thru 2 micron or better spin on filters=like doing a ****** flush & fill on reg. vehicle. Cuts down on time and $$ of a regular change.:thumbup:

Just wanting some feed back DIY or purchase unit if worth while or purchase outright?

VNC 1/2x9/16 #3925 Wrench in as found condition. Marked on reverse with #8742 steel content with the beautiful Nickel Chrome finish. No previous owners marks or grindings/other than factory. CCC at owners risk of sending or USPS M.O. for payment/.no electronic funds.-Lower 48 shipping...

I would concour with a roll like this-only to add if you don't oil your tools and are left in a humid trunk/auto/vehicle they could possibly rust-might not be your favorite to look at with a stained canvas roll, but keeps your tools nice. I myself prefer the WAXED canvas type from China/cheap...

Looking for one (1) only-good condition Snap-on nutdriver #114 that is with the Yellow sq. dr. handle, 7/16" drive and Brown sleeve over the shaft. Normal box wear condition preferred-just no grind, previous owners marks other than factory. I can purchase outright(with m.o.-no elec.$$) or...

Reasonable offer? Trade for a ratchet?:headscrat

13"x8 5/8"/1 1/2" deep looks to be well made and HEAVY! Nice red PJ and the ends have flanges for like fitting down into the box top? Looks like it was not used and orphaned from the box. Anyone seen one like this or know who the mfgr might have been? Thanks......Cranky:headscrat

Correct wrench to NOT scratch your nozzle-9.95 on 10 scale SuperChrome finish. $15.00 delivered to lower 48 address--carefully concealed cash/usps money order--NO electronic funds. Check out the pics and LMK if interested & thanks for viewing...…….Cranky:thumbup: