Search results

Is there a repair kit or parts available that would replace the pin with a regular ball? If one could be changed to a 3/8 drive would be great since I am in need of a new short handle 3/8 anyway Sent from my SAMSUNG-SGH-I537 using Tapatalk

They have a hole with a split ring in the handle so they probably are tethered Sent from my SAMSUNG-SGH-I537 using Tapatalk

I bought 2 williams 1/4 drive ratchets a while back and I can't get a socket onto them easily I have to wiggle sockets on (off is no problem) the problem I am having is keeper on most ratchets is a ball on these it is a round pin with a square cut on the end that gets hung up on the sockets has...

I have ryobi 18v with 6 li-ion batteries I don't do anything special with them I leave them deaf weeks I have left them on the charger for days 3 of them are more then 5 years old and still going strong I did kill one of them I fogot it on the back deck and found it after a few days of rain...

You might be able to switch to a lower watt t8 without changing your ballast like a 25w vs your current 32w it would be a pretty cheap easy conversion if the existing ballast can handle it it should be printed on the label Sent from my SAMSUNG-SGH-I537 using Tapatalk

I have both I had the abrasive saw for years it was good enough for me until I borrowed a portaband from a friend and a couple months later I bought a milwaukee deep cut band saw and almost never use the abrasive saw I don't have a table for it but would like one Scooter could you please post...

I added 2 zones to my boiler with only one zone pump and 2 zone control valves they heat my garage and an extra room above the garage they are ~40ft from the boiler and I only had room for one more pump in my control so there's 2 thermostats that trigger the appropriate zone valve and the single...

Il probably make one as well but rather than an old breaker bar a piece of flat stock or pipe would do the same Sent from my SAMSUNG-SGH-I537 using Tapatalk

I have had a set of 6 for a few months as dodge said the handle feels good in your hand the tips seem to fit any hold very well but I can't say how they are going to hold up Sent from my SAMSUNG-SGH-I537 using Tapatalk

3 inch pvc Sorry went back and reread the original post I missed the charger part at first I thought you were talking about the tools Sent from my SAMSUNG-SGH-I537 using Tapatalk

Home depot utilitech 4 ft long about $40 Sent from my SAMSUNG-SGH-I537 using Tapatalk

Ok now I see it I just wasn't looking close enough great idea that I might have to copy thanks Sent from my SAMSUNG-SGH-I537 using Tapatalk

I did you support the bottom of the saw ? I have been looking at the swag offroad band saw table I really like the idea but it's about $150 and I am cheap Sent from my SAMSUNG-SGH-I537 using Tapatalk

Well thanks guys that just cost me $250 If I hadn't seen this thread I would have never known but the side add on for my box 40% off is tough to pass on and a set of the diamond tipped screw drivers There's no longer a local store so free shipping it should arrive next Wednesday Sent from my...

I have 6 4ft leds in my 24x24 garage they are from home depot I forget the brand but they are plenty bright I think they are about 3200 lumen each and they were the cheapest I could find I think they are very equal to a 2 lamp flourecent Sent from my SAMSUNG-SGH-I537 using Tapatalk

I have given up on high dollar edc knives and a sharp knife it's usually sharp enough but not what it should be On occasion my pocket knife has taken the role of almost an tool in the tool box brass bolsters make great hammers so I try to keep cost down in the $20-30 dollar range use it for a...

$3.02 shipping for me why not give them a try Sent from my SAMSUNG-SGH-I537 using Tapatalk

I know very little about the red iron buildings they look like a very strong building but I have a galvalume channel building in a high snow load area I don't know what Guage it is off hand it is thin but assembled it is a very sturdy structure last winter I shoveled it off once it had over 3 ft...

They have both been repeatedly hit with a hammer either to drive the pin into something or pull with the hooked end but no other signs of wear Sent from my SAMSUNG-SGH-I537 using Tapatalk

These have sat on a shelf in my basement for years I have no idea what they are but can't bring myself to toss them anyone have any ideas in the second pic it says Delaware USA 5 Sent from my SAMSUNG-SGH-I537 using Tapatalk