Search results

Look at boat dock and boat trailer bumpers?

Take a look at Leviton's website for residential structured wiring + fiber. I have experience in fiber to the home and fiber to the industry but looks like you mainly need electrical receptacle wiring or wall box? Either way see if Leviton has helpful product or info. They also have small...

lots of good sharpener info on the arboristsite.com forum. Tools too.

You are using #4 rebar (1/2") at close 10" centers. Are they crossed or just one way? If crossed you should tie them at where they cross. You can go higher psi but the large rebar is likely why the guy advised you can get by at 2500. We use higher rating in GA.

Corins, if you can get the guy location 5-6 foot closer to pole you can consider another idea. have a U shaped plan view with shallow back middle area. Put a 3 foot or 7 foot garage rear exterior door and turn into a small "grill with patio area"? Good luck with it.

If it does exist- call the main source..:) http://www.acument.com/products/torx-and-torx-plus/torx-plus-tamper-resistant-drive-system/

http://www.ebay.com.au/itm/ws/eBayISAPI.dll?ViewItem&item=380432517519 ZDMAK Ebay Australia:rocker:

...some plasticized vinyls can affect plastics like styrene, ABS, Lexan. The plasticizer chemical leeches out like a solvent. Worst case is with really soft rubbery vinyls. I have seen plasticized fishing bait "jelly worms" melt almost through a tackle box plus had to troubleshoot rubber seals...

Advance auto, Autozone, O Reilys and Sears have smaller ones

Delta makes an economical 6" round x 4" wide that is okay- I have one except for heavy sanding works well and tracks okay, has vacuum ports and good switch, others- Grizzly Hitachi Porter Cable makes one. Sears one is complicated to me.

Could be a compression molded rubber EPDM or likely a cheaper injection molded PVC (i.e. vinyl) with plasticizers to make it rubbery + flexible. The American "design engineer" probably just loosely spec'd "black rubber" to the asian supplier. Hopefully it will not crack or split later from...

I had the Homelite version someone mentioned- thinking since Textron/ John Deere owned the line it must be good enough. Lasted one part of a season a skimpy trigger snapped and the shaft hub warped as it could not support the motor overhang weight on the shaft. Go with homeowner or 80 series...

A few things come to mind- 1. the building may have been before a setback was required from edge of properties (often anywhere from 3 foot to 25 foot). Your NEW building may be a problem. 2. Being a support for a last pole, the guy wire may need to locate in your neighbors property or two...

Lowes still has more USA products than at The Home Depot. Go over to HD and look at outdoor tool cutting chains, bars, lubricants, files..

U.S. Plastics;) mcmaster carr

What size is your main box rated? Many older houses are not be able to handle a 100A sub to main box? That was why 200+A was mentioned to cover the whole house plus sub. You may only need 60 or 75A for small shop. :dunno:

Do you mean tie down rings. Mc Master Carr carries a number of varieties. Here is a link to a web page. There is one option that would allow you to have a flush to floor thread receiver and install the eye bolt. Or use heavier zinc plated eye bolt...

Sounds like you are asking for folks to weigh in on a very high risk. There are industrial grade cabinets out there to store your materials but even a NFPA requirement is going to require floor mark off larger than your three foot clearance question. There a good welding curtains to add buffer...

Frame it about 2 foot centers with 2x4 framing and deck with a layer of 1/2" plywood bridging over the face of the beams. Secure plywood to beams with shelf tapping 3/16 or 1/4 siding bolts. Then apply sheetrock if desired. Make sure sheetrock is fastened 1/2" off floor if you pan to wash floors.

Using a primer will actuallymake top coat less work as it will **** top coat which costs more than a primer sealer. Make sure it is matched to work with your rustoleum paint system- oil or latex. Sherwin Williams makes a good latex semigloss.