Search results

Hey Andgott...........any updates on your lift install? Got mine coming end of week.......hopefully!

Wondering if there was a specific reason you didn't install RD tile under the Maxjack? Didn't feel like removing posts or something else? I ask because I'm about to install a 4 post lift and was planning to go directly over the RD tiles.

Floor looks great, nice job! Sorry to hear about the mishap on the table saw while cutting down a tile. I had a very similar experience while using my Makita chop saw to trim down my tiles during install as well. After at I switched to my jigsaw and no more problems.

Congrats, looking good. Post up your thoughts after loading up with tools as I'm looking to add another rolling box in near future.

I recently installed RaceDeck diamond tiles in my 820 Sq. ft garage. Had them sitting in the boxes they shipped in (18 boxes) for nearly 6 years. Must have moved those dang boxes at least a 1/2 dozen times! Have to say I love the diamond tiles and they are a breeze to clean and move stuff...

Hey Poor-as far as a 25' coil hose, 1/4" or 3/8" air line and related fittings?

None of the wires hooked on screws as 10 gauge and switch don't allow. This type of screw just insert wire and tighten down clamp. Just really want to confirm I have the wiring in the correct positions for the switch.

Wylie- In terms of distance from the panel the switch I was attempting to install is only 6' from service panel. Lift location which will be the only thing in this 30 amp line is maybe 20' - 25' from service panel. Given above are you saying just eliminate the switch and wire nut black to black...

Figured I'd snap a couple more pictures to confirm I'm not going to burn my shack down or light myself up before flipping breaker back on. Below is how I wired the switch.......both black wires (one from incoming breaker and other from outgoing to receptacle) wired to the black screws and both...

Ran into same problem. Quick visit to local hardware store and/or HD solved it with these. Cheap and easy to use. http://www.ifinishedmybasement.com/wiring-a-basement/electrical-box-extenders/

Nice 3 car layout and good spot for the lift. I like position #1 for the motor, out of the way and near the power source. Some lifts require 30amp service so take a look when selecting your lift as you may need to make some changes to your power supply. I just placed an order for a lift and mine...

Thanks for all the comments. Built garage 6 years ago and finally pulled the trigger on a lift after lots of thought and research. Placed my order for a Bendpak HD-9, RJ-45 Rolling Jack w/accessory kit as well as a set of casters. The lift will be installed by experienced and certified Bendpak...

I believe the 30 amp circuit is wired with 10/2 as it has a black, white and copper ground. The red wires you see were part of the thermostat which I am removing and looking to replace with a 30 amp double pole switch (MS-303). I think what I wrote above was incorrect in terms of proper wiring...

If I install this MS-303 switch my understanding is both black wires on one side of switch and both white wires on the other opposite side.....correct?

Meant to include these pictures of the wiring to the thermostat. Breaker/service panel is nearby on wall, maybe 6' away. Last picture is the 30 amp switch I picked up, MS-303 instead of MS-302. Difference appears to be the 302 is rated for 2 1/2HP and the 303 for only 2 HP. Motor on lift is 2...

Ok, so another question. Any reason I can't just remove the thermostat on this 30 amp line and use wire nuts, black to black white to white.....button it all up and end of discussion? Not against throwing a switch in if that is the 'safer' way to go but need to track one down, not a big deal.

As for the MS302 switch, a few others recommended same one. I picked the MS303 as they didn't have the 302 in stock and I didn't realize the difference in HP rating. I'll shop around for the MS302 and see what I find. Thanks to all for helping out!

Thanks Cort as I would rather do exactly like you suggested and replace short pigtail with longer 12-15' cord, install 6-30P to end and plug directly into 6-30R receptacle. That link for the 10 gauge 3 wire is perfect as what I think I need.

Ok hoping this is the last question I got to bother you guys with but my electrical experience is limited and not wanting to screw this up. Picked up the recommended plug (6-30P) and receptacle (6-30R), both rated for 250V. Also picked up 30A double pole switch (Leviton 3032) but not so sure it...

Excellent progress, especially considering a one man show.......slow and steady keeps the back problems in check!