Search results

My lift keeps blowing off the return line at the end of the cylinder. One time it broke the fitting one time it split the line and this time it just blew the line out of the ptc. This is the 1/4" plastic line that runs back to the tank. Now the manual says that this line is to return fluid to...

Looking to buy a 4 post lift, located in the Philly tri-state area. I am willing to drive so go ahead and reach out if you are not sure if you are in that area. lol

So my cheap Harbor Freight air hose didn't even last 1 year and its popping and cracking on me. I would like to replace it with a flexzilla hose, but I am not sure how it will handle being pulled and tugged from the reel. What do you think?

Do you guys think that these tools would have any value? I got them from a friends garage I cleaned out, not sure what they are worth though.

http://southjersey.craigslist.org/tls/5009087188.html

Guys I am cleaning out a garage for someone and I inherited some tools. There is a South Bend lathe model 333-a it is a 11 with 4 swing. I have no idea how much something like this is worth, but it works and has tons of extra gears and chucks and such. Also had some old craftsman table saw...

Hey guys my moisture trap is leaking air at the bottom where the threads are inserted into the glass. What can I use to seal this up? Im sure the factory must have used something good when they did it and this is probably just a really old tool.

Ok so I have a picture here. I need to get my air from the compressor on the right to the reel that I want to mount near or on that pole far left. I also need to install the regulator and water separater that you see on top of the elec box. The way the hose reel mounts the air feed has to be on...

Ok I am about ready to put my workstation together and I am trying to figure out what I want to do. I have some base cabinets that I can use for now, until I get some nicer metal ones or build a standard lumber based bench. I would like to have a vise on the end of the table but not sure what...

I finally finished my ceiling and started installing my new ballasts in my lights. Now I am ready to move on to the installation. I have 8' 4 bulb t8 fixtures. I am going to run 3 rows of 3. And I would like to but them up against each other and run the wire inside. I would like to also put 6...

I would like to know if I can flush mount these t8 fixtures that I have. I would also like to mount them end to end with all wires enclosed. If I can.

Ok so I was given 8 8' 4bulb t8 fixtures with the reflector and all. The only problem is they all have 277v ballasts in them. 6 of them are e4/32is-277sc and the other 2 are triad. What is a nice cheap ballast that I should use? Thanks.

Yesterday I was able to pick up a bunch of 1.5" polyiso boards for $50. I would like to just put them against the metal siding in my polebarn by cutting it to fit between the purlins. Then put sheetrock over it. I am located in south jersey. Do i need to put up some kind of vapor barrier...

I have a 24x32 door is on the 24 side trusses run 24 side also. I have 9 8' t8 lights with reflectors. I was thinking 3 rows of 3. My trusses are on 4' how should I attach the lights? I was thinking also put the lights on 3 switches with rows front to back so i can turn the ones above the...

This isn't garage related but I didn't want to join another forum, and was hoping someone could help me out. I need to build a porch for my wife (it was part of the new garage deal) It will be a roof coming off the back of the house the rafter span will be 17' 4". I was planning on getting...

I am putting a 200amp panel in my house and using the 100amp on in there for the garage. The 100 is a bryant and has all brd breakers. The 200 doesnt have a name on it but i have a challenger a sq. D and a eaton br and they all seem to fit? I would like to take all the brd breakers from the 100...

When I had my barn built I had them add a post in the floor plan for putting a loft over my work bench area. The loft would be about 12x8 the posts supporting the weight. I don't ever plan on this being a living space or anything there will only be about 3' clearance up there, it would just be...

I am considering using some 1/2 4x8 polyiso foil faced for my ceiling. My trusses are spaced 4' on center. I was wondering if the panels would be able to hold that span? My ceiling is 12' high and I figure this is probably the cheapest and easiest way to finish the ceiling and get some...

Ok So I am going to bury some 2" pvc for running my elec. to the garage its about 108'. I read that the pvc needs to be buried in a 18" trench. But I am a little unclear. I have dug about 10" for the whole trench and as far down as 22 in some places, but I am getting tired of digging, so I...

When I do the grading and soil/grass around the barn, should I go all the way up to the metal or stay a certain distance away from it down the skirt board? Also I have the waiscoting with the 2 colors and it has that "z" channel and when it rains I can see water sitting on it isn't this going...