Search results

I have a MAC TOOLS 1/2" drive digital Torque Wrench- model TWVA250FD. Its about 15-20 FT LBS off. Does anybody know the procedure for recalibrating this? I can send it off to MAC but dont really feel like paying $100 for them to recalibrate it, if it's a simple procedure. Does anybody have...

wanted to install a GFI outside my garage, but it kept tripping the upstream GFI that was first in the circuit. This is the circuit: The wires from the Panel box come into the first GFI outlet in the circuit, and attach to the "LINE" side of the GFI. I then have wires running from that...

I'm installing a MoHawk 9klb 2 post lift, using the exact anchors the company says to use and above minimum requirments. Mohawk requires minimum of 3000 psi concrete (I used 4000 psi) at least 12" deep (Mine is 16") and enough space around the pad that the Anchors are at least 6" away from...

hey Everyone I have a question understanding the difference between 220 volt outlets and 240 volt outlets. I saw a video online of someone adding, as the video describes, 220 volt outlets to their shop. He opens the panel, and obviously by means of a double breaker, connects both hot poles...

This is a device that applies resistance to a coolant circuit in my car, to tell if the coolant gauge is working properly. The switch has three positions and Each position puts more resistance on the circuit. I see the Resistor but what are those 2 other black cylinders? I think they are...

Hey quick question that maybe you AC guys can explain. Obviously when you're charging up an automotive AC system, it is accomplished by filling on the low side. The freon in the low side line comes from the evaporator as a low pressure gas back to the cars AC compressor. However, I noticed...

Hey everyone. I'm wiring in a 220 volt outlet in my shop. It will be for using a plasma cutter. My question is what gauge wire and breaker amps would you use? I'm thinking a 10 garage (10/2) and a 20 amp double pole breaker but Want verification before I proceed. Thanks in advance everyone...

So im building a small metal forge out of FireBricks. I want to fuse them together. My question is: Since these are FireBricks, will any fine cement work or is there a special kind of cement that i will have to use?....I want to cement the blocks together to form a little oven and the cement...

I have 2 SUN ignition scopes and a SUN distributor tuning machine. I know that SUN is no longer in business but is there any company that services and repairs these machines. One of the scopes doesn't work and the other one partially works. Thanks alot

Hey everyone. I have a Robinair AC recharge, recovery and recycle machine. It is missing the low-side hose and the unit does work. It is is "good" condition. It is a model 34700. I cant seem to find alot of these model units on the net. Does anyone know what the approximate worth of this...

ok..I am trying to find a QUALITY, MADE IN AMERICA, manifold gauge set for servicing car AC systems. I have been unable to find any, besides SNAP-ON or MAC.....Does anyone know of a company that sells such a thing or is every company besides SNAP-ON and MAC all made overseas/cheap garbage??/...

Ok guys....I want to weld together my own bearing press, preferably a 20 ton capacity press, for doing wheel bearings, ball joints, etc....My question is, DO THEY MAKE BOTTLE JACKS WITH FLANGES OR MOUNTING SURFACES ON THE BOTTOM SO THAT PEOPLE CAN DO PROJECTS LIKE THIS?? I have searched and I...

I am looking for a Toe Board to adjust the TOE Adjustment on a vehicle. I am also looking for a Camber Angle Adjustment tool for adjusting a vehicles Camber angle. Aside form the older guys, there may be some who dont know what these tools are. For those of you who don't know what a TOE...

I have 3 pieces of Rubber Collapsible Exhaust Garage Tube for venting a vehicles exhaust out of the garage. Simply slip one end if tube of exhaust and stick the other end outside. Each piece measures approx 10 ft long and has an inside diameter of approx 2 3/8". I would like to get 65 for...

Ok fellas, help me out here...I am looking for certain garage items. If anyone has any available, please feel free to contact me. I am looking for: - A rolling battery Charger (Snap-On, Mac or brand name) - A Toe Board and/or Camber Angle gauge for doing wheel alignments (Im old School...

I am looking for the following items: - Toe board for doing wheel alignments - Camber Angle gauge for doing wheel alignments - Spring Compressors contact me on here or text/call at 845-325-3266

I am selling TWO, 2" deep drawers for the KRA2411, Classic 78 tool boxes. These drawers are Royal blue in color and do NOT come with the ball bearing tracks or the plastic drawer stop (both of which can be ordered through Snap-ON). These drawers are in excellent condition. The Snap-ON part...

Hey...I am looking to see if anyone has a BLUE DEEP drawer (4" deep) from a KRA2411 Classic 78 box that they are willing to sell.. I need to replace two of the top 2" deep drawers with one 4" deep drawer. If anyone has any available, then please please contact me. Thank you. For faster...

I am looking for either Snap-On or Mac tools, 1/2 drive SHALLOW impact sockets in both millimeter and Standard. If you are selling any of those sets, or both, please contact me. Thanks, Dan