Search results

I am selling a Rigid TS-3660 table saw. It was used for one project (built-in desk in my home office) and I really haven't used it since, I have a baby coming in February and going to probably need the extra space in my workshop as well. The saw is one of the best in it's price range and...

I just picked up an Echo PAS setup and my old storage methods no longer work. I have pegboard but it's probably not strong enough for this...I can mount a 2x4 to the studs though. Looking for ideas for this wall: the red lawn tools will not be used anymore so no longer hung up.

I am comparing the Echo SRM-225SB to the PAS setup... Currently I am using a line trimmer to edge and trim wonderfully. I don't know if I really need to go to a metal edger. However I do want to upgrade my hedger and a power head combo seems the best bang for buck. Anyone have experience...

I need to replace all my tools pretty much due to a robbery. It's a disaster as I constantly find myself halfway out to my workshop to do something around the house only to realize there is nothing left. :( I had a pretty good set of tools going...it's my passion really. I was brought up...

I have been happy with my Grass Hog 18V by B&D, but the batteries lose their life too fast. The blower is a PITA and I have to carry 4 batteries to do just my front yard and it's slow. The hedger runs forever, but only good to 1/4" branches. My hedges are coming out more 'freehand' looking...

I was robbed and they smashed my gate. It's 13' total and divided into a 3' 2" people gate and a 11' rolling section. I want to redo it for security with a lock (accessible from both sides if possible). It butts up to a concrete block house and a wooden fence on each end. The ground is...

Paladin 4910 SealTite Pro & connectors $128.45 Harbor Freight 41482-0VGA SAE Taps $74.54 Harbor Freight 41481-0VGA Metric Taps $74.54 Compaq Armada M700 $738 1GB Ram $38.99 Logitech MX620 $46.98 USB Hub $4.97 Incra TRule $42.95 Incra 1000SE $104.68 Incra Miter Express...

I have a driveway gate that spans 12.5' total. There is a 4' section for the 'people' and an 8' that I can swing open (pinned by a stake in the concrete and supported on two wheels). This is a picture of it (sortof...)..you can see the larger section and a bit of the smaller in the left side...

I was thinking just picking up some U brackets but the smallest they come is 1/2". What have you done to attach your leader hose to the wall? I only have a 8' run which about 1/2 of it would be reel to wall and then wall to compressor which doesn't need to be attached. The other 4' I want to...

What is the technique to get that matte finish? Thanks

nm user error

I have old awning anchors and the strip of metal the top hinge slid into. I'd like to remove them. They have large nail head on them and don't want to pry out. Is the best way to just cut them with an angle grinder/cutoff wheel then patch the wall? Wondering if anyone here has any tricks...

looking for a router used, new or other :) $150 is my price point.

I will probably just buy another one (K2 Smartset by K-Rain), the filter looked fine but I flushed it anyway. The sprinkler will pop up but not turn until I reduce the pressure slightly and restore it. Sometimes it works fine without doing this. Is there anything I can 'clean'? The manual...

Looking for a drill press sub $200...these come up time to time for that price. Goes down to 250rpm for a nice metal drilling speed. Anyone own one now or ever? pros/cons? Thanks

Looking to complete my box. 1/4 drive: 1 1/2" ext NutDrivers: 5,6,8,10,11, 3/16, 1/4, 5/16,11/32, 3/8,7/16 3/8 drive: SAE: 12 point: 1/4, 5/16, 3/8, 7/16 6 point: 1/4, 5/16, 7/8 Metric: 12 point: 6, 7, 8, 9, 11, 16 6 point: 6, 7, 8, 20, 21, 22 1/2 drive: SAE: 6 point: 7/8...

I have a bare concrete working floor. It's clean but hardly uniform in color. It's always been a working garage (previous owner was a engine/welder guy). I was thinking of VCT, but I am not sure if I want that especially when I am hard on my floors and it'd be alot more work. If I do...

I am thinking a 12-14" should be plenty...I do intend to make some adjustable bookcases with 12" stock. I'd like to sand the edges of some larger boards. Sears has the 12-14" delta and craftsman around $200. I'd like a floor stander. Anyone know of any deals? What would slightly more money buy?

I picked up a sears deal on a compressor for my smaller workshop. Storage is a premium so I came up with this:

I am looking for the following to finish off my set. 1/4 drive: 1 1/2" ext Nut Drivers: 5, 6, 8, 10, 11, 3/16, 1/4, 5/16, 11/32, 3/8, 7/16 3/8 drive: SAE: 12 point: 1/4, 5/16, 3/8, 7/16 6 point: 1/4, 5/16, 7/8 Metric: 12 point: 6, 7, 8, 9, 11, 16 6 point: 6, 7, 8, 20, 21, 22 1/2...