Search results

Is it worth restoring?

Looking for commercial quality Christmas light supplies to build my own stringers. Never done this before, so recommend me a good place to get supplies. I will go C9 led, but know nothing so what bulb is best. Thanks

I have been wanting to do something with these doors for awhile. went from this. I stained the boards to this I'm very happy with the way they turned out.. Whatcha think?

I have inherited an old Craftsman bench top drill press from my dad. Model 351226250. Has a Renox R33-13L chuck. Can’t find any information on it anywhere. Does it press on or thread on? Seems to have a little wobble in it and the teeth on it are worn down to the point the key doesn’t work on...

For using with a Drill/Impact Driver/..Anyone have experience with these? I see a lot of these on amazon, but I want a good 1 about 12-18", would be using to work on cars & household appliances.

I would like to see what it would look like with the fridge black and the cabinets the color of the door. And i would like to see what color looks good for the panels of the garage door. Just a light brown, something that blends. Open for suggestions. Thanks

Here's what I have going on. Can this be painted? I believe it's a tempered hardboard (Masonite) panel and as you can see moisture is starting to bleed through. If I can paint, I would use Kilz first of course, or some type of primer. Should I use enamel or latex? Any other Ideas? Post...

From these pics you can see I have a recessed area where my lights are, I would like to get lights to the sides of my cars. I was thinking of using an adapter to screw into the opener light, run some metal raceway to the light, wire up a plug to the end of the Romex to plug into the adapter. I...

I would like to install a Wall Mounted hand sink in this area, with back splashes above and to the side. Don't think I want a cabinet. Just trying to keep cost down. Not going to be used everyday. Anyone have any recommendations on a brand? Elkay, Krowne, Advance Tabco, Eagle Group, John Boos...

I have a Stand up Freezer in my garage that I would like to paint Black, it's white now(factory finish). What would be a good HARD, Durable finish. I want this to last and not scratch. I would prefer to roll it on, not SPRAY. I do not have a spray gun. If I have to use spray cans to get the best...

Anyone have any experience with these? Runs on Battery, 120 Volt and Propane. Dewalt https://www.homedepot.com/p/DEWALT-27-000-68-000-BTU-Cordless-Hybrid-Forced-Air-Propane-Portable-Heater-DXH70CFAV/309809370 Ridgid...

After Hours of research of what to put on my floor, I finally pulled the trigger on the tiles. I was going to go with a Polyurea coating , but for a little more money and a WHOLE LOT LESS work I decided on the tiles. I worked up a few (Many)designs but couldn't make up my mind , Justin suggested...

It's an attached home garage. 646 sg/ft No major work happens in it (brake changes, shocks, I have changed out some tie rods) so a floor jack is used.. I think it has been sealed. Water stands on it for days from car AC drainage. (see pics below of water) There is some damage that needs...

I am just surprised there isn't much posted on here about these tools. I have been debating about getting into a battery platform and was really leaning towards Milwaukee, but I am having a hard time justifying the cost of their tools since I am just a DIY person that wouldn't be using these...

I have been looking at the 2 & 4 gallon models. Anyone here have them? I like the prices on them compared to Milwaukee and others like Flowzone ect. Just can't see paying over 200.00 for home use. My concern between the 2 & 4 gallon is that the 2 gallon wand seems to be better (I believe its...

Just pick up a Light that uses 18650 3.7v Li-ion batteries, would like to replace the 2200mAh 1 with a better 1 and have extras on hand. Thanks Ed

I am stocking a new tool box. I am just a DYI occasional home user. I have a set of Reg. Combination wrenches and want to get some Ratcheting Wrenches. Should I get? 1)Reversible Ratcheting Combination Wrench 2)Flex Ratcheting Combination Wrench 3)Flex Ratcheting Box End Wrench Thanks Ed

I have 3 of these that I would like to replace with a 4ft led or something better. What ever I use I want to remove the current fixture and hard wire into the current location since they are on a switch, and surface / flush mount to cover the hole. What are some reasonable priced...

As a home user would this be a good purchase for removing lug nuts, outer tie rod bolts, stabilizer bolts, shock bolts, and other front end parts? I have read conflicting information about their ability to remove these. So I wanted to ask those that are using them. Thanks Ed

Why doesn't anyone make Blue Wrench Rails? All I see are Black or Red.