Search results

Looking to pick up a few things on eBay. Any info on when they will have their next 10%-15% coupon.

Hi All, Recently purchased a plug-in hybrid and want to put a level 2 charger in my residential garage. I previously installed a sub-panel so have plenty of room for the breaker. Just want to make sure I get the right type of wire. It is approximately 70' from panel to where I want to mount...

I have two fixtures on either side of the entrance door to my house. They have photo-sensors and a standard light switch inside the house (next to two other interior light switches which share some of the wiring). I recently replaced the incandescent bulbs with LED and notice something...

Good place to buy stuff like Leatherique Happy New Year to our AutogeekOnline Forum Members! What better way to start 2018 than with an exclusive 25%* off savings code!? Use code FORUM25 for 25%* off your order! PLUS - All orders over $50 SHIP FREE!

Hi All, I am a total hack fabricator, so apologize for misuse of terms. I would like to mount my winch (Badland 9,000) in tool box on my aluminum flatbed car trailer. Due to lip of trailer I would need to raise the winch approx 7" inches from the floor. I was thinking of a big aluminum...

Just curious if anyone has seen one of these. Looks great. No idea on the price but I'll bet it is not cheap. http://www.sviinternational.com/sites/default/files/SC-363%20Porsche%20Lift%20Brochure_3-page.pdf

Came across this for cheap. Says Ster-Draulic, made in Detroit. Can't find any info on it or the company. Any insight?

I've been looking to buy one of these for a while but they have been close to $90 plus dollars forever. Now on sale for $50 on-line at Pep Boys (Store pick up only), or PepBoys via Amazon with free shipping. I went with the latter and had it at my door in two days...

http://m.sears.com/craftsman-c3-19.2-volt-lithium-ion-drill-and/p-00947695000P

$85 dollars on Woot http://tools.woot.com/offers/m18-xc-4-0-starter-kit

Hi All, I recently purchased a used Snap-on midrise, made by wheeltronic. Sometimes it will get "stuck" in the up position. If I wait a few minutes and try again it will usually be fine but I worry that the problem could get worse with time. I am theorizing that perhaps it is the pressure...

Hi All, Am in PA and just bought a Honda EB12D generator from Nevada. It is a self contained "silent diesel" style on wheels, weighs in at 750 lbs. The challenge I now face is getting it transported. I thought being on wheels would make it simple and have listed it on uship. Turns out that...

As noted in other postings, Griot's Garage offers some decent torque wrenches made in the UK by Norbar. One of the big selling points of the Griot torque wrenches has always been that you could send it in annually for a free calibration. Unfortunately, this is no longer the case as I just...

Hi All, I am looking at two used compressors. Both are in the same condition, about the same age, with similar specs (7hp, 80 gal, 24cfm) First is an IR 2475n7 2nd is a Snap-On bra718v I realize that if bought new the Snap-on is way overpriced. However, given the equivalent price of the two...

Thanks for all the advice from members. I came close on the Quincy but could not swallow the price. Almost went with the 7.5HP US General from Harbor Freight. The specs, Baldor motor, and price were tempting but I worried about depreciation if I ever need to sell it. Today I found a used...

Any one have experience with this unit. Specs and price look decent: http://www.fscurtis.com/store/index.htm?t=&hp=&id=2 Not sure about what brand motor it uses?

Hi All, I am looking to buy an IR compressor to replace my aging 25 gal Craftsman which lacks the oomph for my new blast cabinet. The two I am looking at are both 5HP. The one from Northern is the SS5L, 60 gal, single stage for $879 delivered. (plus liftgate fee)...

Hi All, I recently purchased a ProPark 8S 4-post lift from Greg Smith Equipment Co. This unit uses a ladder-lock system. Set it up this weekend and am pleased with my purchase. I did have a few questions that I hope others might be able to help with. 1) My garage floor has a very slight...