Search results

I need to place an order for 3 cans of TCS13 Toolbox cleaner. MAC won't allow me to order less than 12 cans. Also could use 3-4 of the MAGMF as well. Please send PM Thank you

Please ID this vise. Thank you

If you have a Snap-on BF612 hammer on the truck and would like to sell it please contact me. Thank you

I have a Delco M16-109 Ignition cable tester. It is complete in very nice shape. I need to know what size battery and voltage this tool uses. The space where the battery goes is not a standard AAA, AA, or C size. The instructions do not mention a battery. Does anybody know what size and...

I have an Eagle Lift with a push button switch. The switch has a waterproof cover that needs replaced and I can't seem to find one. Original manufacturer no help Specs M10X1.0 Thread Total length 5/8"

Older Snap-on ratchets from the mid 1970s and 80s had a small round Snap-on decal on the back head of the ratchet where the stamped logo is today. Is this decal still available? TIA

I have the following 3 dial indicators: Federal C81Q, Randall Strickney C1608 & Starrett 8617. I would like to know the specs on these dial indicators Info such as the graduation (.001 or .00001) total range of measurement, accuracy etc. I can find nothing on the net about these indicators...

On eBay I have seen Fairmount 12pt single end, line wrenches and cannot figure out why the 12pt rather than 6pt. Is there something I am missing? Every other line wrench I have seen has been 6pt for a more positive fitting contact to prevent rounding off the fitting either loosening or...

Does anybody know anything about this tool? It is a pneumatic slide hammer tool number 658. Last Fall Astro Tools released it, there were some reviews on YouTube and then **** gone. I have tried contacting Astro Direct crickets, PMed Astro Tools here crickets, nothing it is like I dreamed...

I bought this tool off eBay now I need to find out what it is. It looked interesting and I have never seen one like it. Can anyone tell me what this tool is and what/how is it used. TIA.

I am looking for a JH Williams Super Adjustable Wrench 4, 6, 8, or 10" model with the lock button. What years were these available?

As the title says looking to buy a New E-Z SOLDER CLAMP. I had one B.O. for 6 months and MATCO canceled the order. Any dealers with one in stock please contact me, Thank you

I live in the sand hills of NC. I have a heat pump that is 15 years old and works great. When the temps are between 30° - 50° the heat pump will put out air from the ducts between 86° - 88°. My thought is in the last 15 years heat pumps have gotten more efficient and I would like to have air...

I have a few Burroughs Carburetor Tools that I need to identify BT-16 56126 Pump Rod Gauge need application 56127 56128 56130 Float Gauge need application These tools are from the mid 1950s to early 60s TIA

I have a Shinano SI-1108B air ratchet after much research I found it takes a size 10PM fitting (link to fitting below) Problem is I run Aro-Type fittings in the shop and the Small Cupla Type are not compatible. No problem I figure I'll just get an adapter 10PM male to 1/8" NPT female. Problem...

I have a Shinano SI-1108B air ratchet. I use Milton 777 1/4" air fittings in the shop. The threaded hole in the ratchet where the air fitting goes is a bit smaller than the standard 1/4" fitting. How do I solve this problem? How do I get a Milton 777 onto the tool? Do they make Milton...

I have MAC Tools 2 prong socket SC100A and would like to know the application for the tool. I know it removes antenna or dash bezels but looking for the specific make.model/years this tool was designed for. Thank you

There used to be a Vintage Snap-on Tool site where you could go type in Snap-on Tool number in the search box and it would take you to the catalog page with the info on the tool. What happened to it, it seems to have disappeared. Anybody know where it went? It was great for looking up old tools.

Can somebody please post a pictures of the AFR128LFR 1/4" ratchet and the BFR158LFR 3/8" ratchet. Need to see what one I need for a specific application. TIA

Does anyone know of a 3/8" drive lug nut socket set? Been looking but they all seem to be 1/2" drive. TIA