Search results

smaller cabinet to match newage bold? I have several Newage Bold 3.0 cabinets in my garage. I have a spot where I'd like to add a storage unit/locker. Ideally it would be no more than 12" deep and 24" wide. Anyone know of where I could find one, that would match the look of the Newage...

My contractor, when he repaired some mortar cracking on the front of my garage, didn't clean off the mortar from the edges and face of the brick. So the portions repaired look different than the rest of the brick wall. So I'm thinking of either taking a Dremel tool or Angle grinder to these...

I don't normally go out of my way to recommend purchases, but thought I'd share this one... Was looking for a shop stool/chair for my workbench area. Found this one. For the price, highly recommend it. Have been using it for my office away from my office these days. Comfortable for use over...

I recently set-up an old Altec-Lansing PC speaker system in my garage and was surprised how great it sounded. Only issue is that I have to connect it to my phone or ipad to play Sirius/Pandora. Does anyone have any recommendations for a good wireless to 3.5mm jack adapater? Spotted the below...

Looking to replace my dated fluorescent under cabinet lights with LED ones (in my kitchen). Does anyone have any recommendations? I spotted these: https://www.ledlightingwholesaleinc.com/UCA-24-WHT-p/uca-24-wht.htm...

Looking to get a set of adapters for my 2-post Rotary lift. 2 of my cars have pinch welds by which to lift the car. (I know that it's possible to lift directly on the pinch welds, but i'd prefer some sort of adapter). Looking at the below (kinda of cheap but good reviews). Anyone have one to...

My existing drill is biting the dust... So will be in the market for a new cordless drill/driver for all-around home use. At the risk of being too vague... what do folks recommend that is reasonably priced? Thanks.

Getting ready to pull the trigger on some newage bold garage cabinets. Big question is... red or grey? I like red in general but concerned if it's a brighter red (not as good) or more of a deeper (Craftsman like) red (better). Thanks!

From my research, the blue that Rotary uses on their lifts is Signal Blue, RAL 5005. I haven't been able (based on online searches) to link that color to something that I may find locally at HD, Lowes, auto part store... Does anyone know by chance of an equivalent color that I could find at a...

I recently had a Rotary SP010 2-post lift installed in my garage. I'm planning on doing the electrical hook-up. I'd like to run the following by the experts here to make sure that I'm not doing anything wrong: -I have a 3-wire 220V supply near top of the lift post. That circuit has a 30 amp...

I just ordered a Rotary SPO10 2-post lift. (Looking forward to it). It comes with wedge anchors 5 1/2" in length, that I think will embed into the slab to a depth of about 4" or so. Where the posts are I had the slab poured thicker...~8" thick. And my concrete is 4000 psi with wire mesh. I...

Looking for a reputable 2-post lift installer in the Greenville, SC area (including Anderson, Spartanburg...). Thanks.

I'm about to order a challenger SA10 lift. Finalizing the lift placement and orientation. I'm probably over-optimizing, but I figure why not make it the best possible. So... what I'm looking for: -ability to have one car on the lift while having the second car in the garage -ideally I'd be...

I'm getting close to pulling the trigger on a Challenger SA10 2-post lift. Fits my criteria... not the cheapest/not the most expensive, certified, symmetric, slightly less that 12' (left post is under a sloped portion of the ceiling @ 11'8"")… I've attached a sketch of my plan. I built this...

I filled my saw cuts with Sikaflex self-leveling sealant today. First time I've used such a product. Worked great. The saw cuts were about 1" deep so I used a foam backer to make the depth about 1/4" (width of cut was about 1/8"+). Some have recommended taping to prevent messing up the...

My builder installed an entry door and a French door on the side of my garage, and the slab that the doors rest on is slightly sloped from the rear of the garage to the front (as it should be). Due to general incompetence in my opinion, they didn't support the doors' thresholds in any permanent...

My contractor recently sided my detached garage with hardie board lap siding. Unfortunately there are hairline cracks visible on the lower edge of the siding below nails (that were driven below the surface). I'd estimate that a quarter+ of the nails have a crack visible, and probably about...

My new garage's brickwork was done about 1 month ago. Attached are some photos of cracks that I just noticed. There's a long crack above the garage door going diagonally for about 4' or so in the first photo (open up the photo and you'll noticed it). There are a couple other short cracks, as...

Will have a 8' X 16' garage door on my detached garage. With a single row of wide panel windows. Should i put the window panels on the top row or 2nd from the top? If you have a picture of yours - please share. Thanks.

My new garage is near completion and am planning for painting it inside... What do folks recommend for ceiling paint? Standard (flat) interior ceiling paint or something different? Thinking of painting the walls 'eggshell'. Thanks.