Search results

I had a Shapeoko XXL and it was pretty user friendly. I upgraded to a OneFinity and it will be arriving in a few weeks. It uses ball screws instead of belts and can be assembled in under a half hour. https://www.myerswoodshop.com/blog/onefinityvsshapeoko Sent from my iPhone using Garage Journal

I tried the column cap and it might fit. I would have to file down some ribs on the cap. I took apart the motor to show everyone the state of the insulation on the original wiring. I may attempt to solder in some new wiring or heatshrink over the original wiring. I will repack the bearings as...

Cincinnati, OH

Yes, I have been searching Facebook. craigslist, letgo, and offerup. Hopefully, something will pop up. It is hard to find a new motor with a 1/2" shaft.

Thanks. I just ordered some Grez Off from Amazon. Luckily, I have Bar Keeper’s Friend and Paste Wax. I’ll have to check to see if the column cap fits. Otherwise, I found a plastic version on eBay. I’d prefer chrome, but plastic would be fine in a pinch. The original switch on the head wasn’t...

I finally set up my old Atlas drill press. I plan to clean off the grime and polish the chrome, but leave the original paint. I like the patina look. I decided to open up the motor to check out the wiring. Most of the internal wiring inside the motor is very brittle. The motor is a Dunlap 1/3...

I used shrinkwrap strapping as extra supports between the ribs. I originally put those up for the original tarp. I had issues with water pooling in the saggy Shelter Logic tarp. The strapping help keep the tarp from ripping from the weight of rain water. When you shrinkwrap a boat, you make a...

I shrinkwrapped my Shelter Logic frame after the tarp fell apart after a few years. The shrinkwrap is about 1.5 yrs old and is still holding up. Shrinkwrapping has a learning curve to it if you use one of the cheap torch guns, but it isn't terribly difficult. I started using a Shrinkfast gun and...

I went with Rubbermaid Fasttrack. I need to get some more S hooks to hang things. You can get attachments to hang hoses, basketballs, shelves, etc.

I bought a Beacon Morris 45k heater on sale at Menards in September for $389. I'm sure the prices are the highest this time of year though.

I think the Beacon Morris manual calls for a minimum clearance of 18" from the fan to a wall. I'm still in the process of mounting one in my garage.

Nice E30 and E36 M3s [emoji482].

Hi, I've been a member for a couple years, but rarely post. I bought my first house last December and am finally getting ready to start fixing up my garage. It's an attached 22'L x 29'w x 10't oversized two car. It is insulated and drywalled. I'm planning to install a 45k Beacon Morris heater...

How much were the Artic Cove misters? My local store had them on clearance for $79 last week. I'm wondering if they didn't update the sticker on purpose. If you wouldn't mind, could you please post a picture of your receipt? Here is what was in my local store last week.

I went to my local store around 9am as well. They let me buy the display model though. It saved me time not having to assemble it.

Yes, HD matches the 11% rebate. https://www.homedepotrebates.com/11percentmatch/

I have a 10 gallon California Air Tools compressor and it is unbelievably quiet. I plan on plumbing in another tank for storage. If you do a lot of grinding or painting, you would need a much bigger compressor. It suites my needs for light tasks like installing wood trim and filling up tires...

Does anyone happen to have a current coupon for the 2 ton low profile jack? I found coupons for the low profile 3 ton in Hot Vws, but no coupons for the 2 ton. I also searched the Harbor Freight thread a little bit. I really need the 2 ton for the extra reach. Thank you.

Reel #2 looks like a Craftsman Professional. I just bought one yesterday at Sears for ~$50. I will be checking to see if there are any K Marts near me that are still in business. Nice scores.

Got mine today. Thanks Op!