Search results

Snap On will warranty it. Cornwell also carries it as well. One of my technician got a set off the Cornwell shop after using mines that I got off the Snap On truck. I'm not going to say they are built well, but they are very useful when the need for it is there. I broken the 17mm 3 times now...

Haven't been on much. The bench is holding up very well. I still kept the white protective plastic wrap that is on the stainless steel top. I didn't want to get it scratch much so I got two pieces of MDF boards cut from Homedepot to sit ontop of the stainless steel top. It went through 9...

Maybe in Albuquerque, a creeper is difficult to source out?

I have a 4Sevens Maelstrom that I used at the shop. It's 800 Lumens and runs on RCR26650. A special rechargeable battery made for the Maelstrom. It's equipped with the SST-90 Emitter. Very super bright light. For a everyday carrying light, I have in my pocket a 4Sevens Quark Mini 123 that has...

I gotta somehow find more room for more sockets. Taken a few days ago. And I thought the KRL box are big, going to need more room very soon!

I have AutoEnginuity on my laptop but I don't use it much. Probably 5-6 times a month. I don't use it that much anymore is because I have AllDATA, OnDemand5 and Snap On Altas Programs to take care of most if not all problems. AutoEnginuity works really well if that's the only program you have...

That's a great buy! I have two of those. One is Electronic Control by a Control Pad and the other is a Manual Lever. Use both daily, haven't fail yet. I believed mines is 10k lbs rated.

Does IR have a Boot for it?

Is that Tool Box fully filled? Curious to see how long ago it was and how many tools are in it.

Testing avatar Oops wrong place!

That receipt is older than me!

It's a shoe holder from the old days. The old folks would clamp down the Mob's shoes while they polish it up...:D May not be it but that's what it reminds me of.

I still have 2 sets that's un-open from the box with 1/4'', 3/8'' and 1/2'' Drive trays. I'll see how the epoxy glue held up tomorrow. When I bought them 3 months ago, I was hoping it will come in handy one day. It proven itself not so good. The sockets wasn't pushed together or anything. I...

I think it's an knockoff. I'm going to try to epoxy glue the tabs back in place since it broke at the very bottom where it meets the tray and try to use it for the time being until it breaks again or breaks more elsewhere. Pass it onto my apprentice technician maybe? lol

I'm not sure if it's the heat from towing the push cart outside the shop that cause it crack in some way but from being new just out the box is just not right. I wonder if I can still return this, I've lost the receipt already since it's been a few months ago. I didn't know anything about...

It's a butterfly impact wrench.

Where are the Lowes brand "Hansen" socket tray made from? Location wise? I've bought a few set about 3 months ago and started to use them. They came in 3 per box which includes a 1/4'' Drive, 3/8'' Drive and 1/2'' Drive Tray for Shallow and Deep Sockets. Earlier today, I started to use them...

Been using the Snap On 3050 for a little over a year and half now. Works flawlessly. I also have a Mac Tools Long Barrel Air Hammer as well that works as great as the Snap On 3050. I bought the Mac Tools way before I bought the Snap On, but I still find time to use both.

If prybar doesn't work, I use Air tools. Snap On Air Hammer with a Bent End Chisel works great.

Not regarding a Socket or Ratchet from Snap On, I broke one of those red and black Soft Grip Snap On Screwdriver before. Showed it to my Snap On guy and he replaced the Screwdriver shaft for me as well as the Soft Grip because it was really beaten up. I used it for everything, pry bar and what...