Search results

Diagnosic Scanners are different then something like a multi-meter or a powerprobe. I'd just suggest going to trade school, and treat that schooling like your job and absorbing as much of it as you can. There is a lot to learn, but it all makes sense. You need a 3/8 impact and a 1/2...

Snap-on hand tools are of very high quality but very pricey. Wrenches and Sockets and stuff its nice to have snap-on but you don't NEED them to be a good tech. Snap-On boxes are nice, they work great, they are smooth, and have a side benefit of broadcasting you are serious about your job...

They get used a lot I find. Usually nothing my ratcheting screwdriver with some 1/4" extensions and various bits on the end can't handle though...

Oh, I may also add that it can also be used as a dielectric grease in a pinch. Use it on your battery terminals, even on your snowmobiles or boats!

+1 on Fluid Film. It's safe enough to drink (though, I don't know why you would), and does a really good job at rust prevention (won't wash off with water easily). Since it is based on a natural and safe ingredient (wool wax) you don't have to worry about additional petroleum products leaching...

Get Snap-On ones on ebay. I have Mac ones and even though they are really nice and super tough, I've been kicking myself since day one because I like the SO ones so much more. Buy once, Cry once.

I'd focus on filling out your set before you decide to blow whole pay cheques on pro-tools. There are a lot more to the 'basics' then Sockets and Wrenches. Get a big enough tool box to allow for a year or two (or more) of expansion. Get a good selection of good quality pliers like...

Grinding them down flush makes them wear really fast, but is AWESOME to cut zip-tie tails nice and flush so they don't grab on someones clothes or skin. If just used for that purpose they last quite a while. I have a cheaper set of Nippers and Side-cutters that I did just that to, and they do...

I have the odd ones that came with certain Genny's, ATV's, Motorbikes, Sleds etc, that always seemed to be only for removing spark plugs in the woods if you accidentally flood the engine. I use one as a sort of breaker bar but only to make Hex Wrenches in my right hand more comfy (cut a tendon...

Beauty!

You could, but I wouldn't. I would personally get correct hose fittings and crimp them on the lines. Less complexity = Fewer Leaks down the line.

http://www.amazon.com/dp/B0002STSOY/?tag=atomicindus08-20 I've had it over two years, and use it quite a lot. I've gone through a couple hundred discs and it's shown no sign of slowing down. Before I got it I was just using a 1/4" Mac (overseas) Die Grinder, and it's so worth it to have a...

I have the Instinct Soft, and the Williams Hard Handles. I'm always grabbing for the SO's, and anybody that says they don't last, are a magnet for dirt and grime, fall apart etc. Has never owned a set and put them to harsh work. Expensive but the best in my opinion. The Williams are...

+1 on the CP, My straight cut-off tool is awesome! I forget what I paid, but I know in my head I was taking a chance buying it vs. the SO and Mac ones. The chance paid off ten fold, it's a tank.

I have snap-on and mac. The Mac are just re-branded Channellocks which were ok until one of the tips bent (still usuable, but they aren't very strong.) The Snap-On's are awesome and I've never had a single problem or complaint with any Snap-On pliers I have.

I have a Mastercraft set that I've had for many years and used often professionally. The main sizes I use a lot (5/16, 3/8, 1/2, M10...etc) I have slowly acquired better quality and have many multiples. That said, the only reason I've gotten extras of the main sizes I find myself using isn't...

I'd recommend the Power Probe version. It does a pretty good job at finding the general area of the short/open in the circuit. There are certain shorts I've found with it's help that would have otherwise taken ages to find. It came with my Power Probe 3 master set, so if you don't already...

They're just Mastercraft Maximum. $30 and they're yours. Bring more money though because I have lots to sell to a tool lover :p

I'm In Mississauga and have a few things I'm trying to get rid of because I'm leaving for BC and need space/weight savings. http://toronto.kijiji.ca/c-buy-and-sell-tools-hand-tools-Snap-On-F731A-Flexhead-ratchet-with-Matco-Silver-Eagle-Sockets-W0QQAdIdZ503592841...

Well on the road I have my work tools, a 40" SO box, with a top box, jammed full of Snap On, Mac, US Williams, Matco, and other really good brands. None of the tools in the Red top box are junk though. I do really love the box, especially because it's made in Canada, and it's really heavy and...