Search results

Don't know how good these prices are but I thought I'd pass along the sale info for everyone to check out- https://www.amazon.com/dlp/4239debe/

Called this morning to check on the status of my order and the rep said that the item is on backorder, and that the price was a mistake therefore the order would be cancelled. She did offer to place an order for the item at the regular price, which I declined. Oh, well- worth a shot....

Thanks to the OP for this- I just picked up the last few bottles at my local store. It showed $3.89 online and in stock (still a deal) so I placed the order last night and picked them up today. I asked if they'd price match them for me since other stores in the area showed them in stock and...

Sorry to bring a thread back from the dead, but a search pulled up this thread- I've got the same situation as the original poster- older, good 2 stage compressor head & motor that was originally mounted on a horizontal 80-gal tank, which was kind of suspect. I have a good 60 gal upright tank...

Well, I called the county permitting office and spoke to someone there- they said that I'd be able to pull the permit myself and that it would cost around $45. I was surprised that they were as helpful as they were, as they said that they could answer questions about the install and venting for...

That's a good point. I never considered if using this would be an insurance risk. Anyways, after pricing out what it would cost me to get the power vent kit, I've ordered one of the Mr Heater units that I can vent horizontally. Can anyone tell me if I need to/should get my installation...

Yeah, 7' would be a bit of a stretch- in order to vent through the roof, I'd have to cut an access hole into the space above the garage in order to route the vent. I think that I'll have to consider if doing that is worth it, or if I'm better off trying to save up for a shop heater with a power...

Looks like you're right- I stopped before seeing the horizontal vent accessory- so am I correct in reading that if I put a horizontal vent with a vertical portion outside the house then I should be good?

Hi, the model is F25- you are correct, it is a gravity vented unit, but according to the install manual here- https://www.rezspec.com/catalog-f.html#tabs-pdflit It can be vented horizontally (in fact that's the way the exhaust vent is installed from the factory) with a 1/4" rise per foot on...

Hi all, I recently picked up a used Reznor shop heater, and mounted it using uni strut in my garage. I've hooked up a gas line that we had installed when the house was built, so the next part of the process is venting the heater. I found a kit that is used to vent the Mr. Heater Big Maxx...

I figure the motorcycle shop I used to work at had more of the 5gal pails and the 30gal cans around because we didn't use as much as the car guys did on race weekends.... We used the 30gal cans from VP, Nutec and Elf as our bench garbage cans...

VP Racing fuel comes in 30 gallon drums- you might want to check with a local dealer to see if they have any empties that they'd be willing to sell you...

Hi all, I was wondering if any knowledgeable compressor folks could help me with a project I'm working on. I recently purchased an old 5hp 220v 2-stage compressor mounted on a horizontal 80 gallon tank. The tank appeared to be pretty beat up and sounded suspect, so I located a decent used...

I use Tygon tubing for my motorcycle vent tubing as well as for some of my fuel lines. It's chemical resistant, and hasn't cracked, split or otherwise degraded on me since I've been using it. I get it here- http://kurveygirl.com/shop/product_info.php?cPath=106&products_id=280 The diameters she...

PM sent regarding Snap On air ratchet.

Hi, the only pictures that I have at this point are from the ebay listing- http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&_trksid=p4340.l2557&rt=nc&nma=true&item=270735742961&si=QwTsnmfrT%252BPcKq3eGdLBmF7Bqcw%253D&viewitem=&sspagename=ADME%3AB%3AEOIBSA%3AMOTORS%3A1123 Any ideas?

Hi all, I've been piecing together the parts necessary to rehab a used compressor that I bought, and found someone with an old Leroi Dresser compressor pump. For $100, I picked it up and now I'm wondering if someone could help me find any information on it. Based on my research it's a Series...

Thanks for the advice all, guess I'll have to keep looking to see if something better comes along... Yup- based on their current model specs, this is 3 running HP.. Guess the dealbreaker would be the sandblaster- big motivation for getting a larger compressor than I have right now would be...

Thanks guys- looking at their current catalog, they do still make a 5hp (peak) model which indeed does make only 11cfm, so I would assume that this is the older version of that model. So if I could get this for $500, would it be worth it for a home shop, or would it be better to save my money...

Hi all, I've been looking for a used 2-stage compressor for my new home shop and came across this on Craigslist- http://denver.craigslist.org/tls/2286823052.html Emailed the seller and he said that he's had it since 2004 when he got it from a shop that closed. Since then it's been sitting...