Search results

I am making a light duty 3-1/2' x 7' cart for pickup up brush and yard waste . I am using 2x2x1/8" steel tubing with a plywood floor. It will be pulled by a lawn tractor and never see a road. I am looking for inexpensive axle ,tire, wheel ideas. No need for springs. What does everyone think...

Check out Greg Smith. Sent from my XT1254 using Tapatalk

What about the stop start limit's, would there be enough travel. Sent from my XT1254 using Tapatalk

Matt_o_70, let me know what you find out. I am looking for a less expensive set up than $600.00. I don't need a commercial unit since I one open this door a couple of times a week. Sent from my XT1254 using Tapatalk

Great idea, you solved my problem. Where is the best place to get a opener with a long enough track for a 13' door ,do they sell extensions ? Thank you Sent from my XT1254 using Tapatalk

Thank you, now I know I have a low headroom set up. The reason for my post is that I am looking for something more elegant. Anyone else have any ideas ? Sent from my XT1254 using Tapatalk

I don't think I have room for a opener. I have three 12' wide doors on a 40' wide pole barn and the shafts almost touch. Looks like propping it open with a 2x4 may be my only option. Sent from my XT1254 using Tapatalk

Hi john. Here is a picture of the track, the cable pulls the door back open. Sent from my XT1254 using Tapatalk

I have a 13 ' high lift garage door that opens 12-1/2' and I need it to open the full opening. I am using a 2x4 to hold it open to the full opening so I can get my camper in an out . The cables prevent the full opening and my installer said a automatic opener would open it to the 13' heigt:(h...

Have you looked at the Atlas lifts, Greg Smith Equipment sells them. I bought a Atlas[emoji768] 9OHSC (SS) and I am pleased with it so far. Much better prices if you want to pick it up. Sent from my XT1254 using Tapatalk

Hi I am looking for advice on the purchase of an acetelene torch set for ocational use. I want to be able to cut and heat to be able to bend steel. I am able to get see special pricing at air gas. I want to purchase the tanks rather than lease along with a cart. Any recommendations.? Sent from...

Does anyone make one that will lift 7000 pounds ? Sent from my XT1254 using Tapatalk

I am looking for one that will lift a pickup about 7000 lbs. And one you can move if needed. Sent from my XT1254 using Tapatalk

Anyone use on of these for a 3/4 ton Crewcab pick up ? Sent from my XT1254 using Tapatalk

Hi, I have a 13 foot tall garage door that opens 12-1/2 foot under normal operating conditions. I need more of an opening to get my camper in the building so I have been propping it open with a 2 x 4 and getting the 13 foot. Does anyone have a solution , like a catch , etc ? Oddly enough my two...

It is a Jet model 13 R . I think I will take the Chuck off and go to a tool shop. Sent from my XT1254 using Tapatalk

Thanks for all your help, I am going to measure the hole size and count the teeth and see what happens. Sent from my XT1254 using Tapatalk

I have a 1/2 capacity drill Chuck on a old drill press and need a Chuck key, the only marking on the Chuck are H2862 ! Any ideas on what key I need ? Sent from my XT1254 using Tapatalk

See about renting a motorized cement buggy. That is what my cement guy used,it like a huge wheelbarrow with a motor. Sent from my XT1254 using Tapatalk

Look at the new Stihl MS180 for $200 bucks,I have one and it's great. Sent from my XT1254 using Tapatalk