Search results

Rubatex, been using it for years in industrial applications for rubber to steel.

I have had a Echo CS530 for about ten years great saw, I also have a Stihl MS391 which is about 8 years old. The Echo is great for limbing trees smaller stuff, although it has plenty of power to buck trees as well. The Sthil is primary used for bucking and felling and is also anti-vibe.

Just ordered a new WEG 5hp 1750 on E-bay for $344 with free shipping for my compressor project. The company I work for builds shotblasting equipment and we have been using WEG's for some time, some customers insist on Baldor. I have had more Baldors fail than WEG's as of recent.

I have had this one for about two years, holds up well and as stated above the x pattern straps are nice.

This is correct. I sell shot blast systems, I see this happen with in a matter of hours in certain locations. I have had new technicians pick up parts with bare hands and an hour or two later rusted finger prints on the part. I was also part of a team that was testing a device that would...

My first new saw was an Echo CS 530 bought new in 09, still have it and use it a lot. I also have a Stihl MS-391 purchased in 12' thought I needed a bigger saw.I cut 7-8 cord a year of oak and drop large trees around my property. Both saws have 20" bars on them although I did try a 25' bar on...

You did well hundred dollar light. I have had one since 2007 heavy use only changed the battery once.

I just installed a Skylink wireless 3 way switch in my shop which is about 250' from the house. Works great but each switch is only good for 600 watts so keep that in mind.

Looking to seal my shop floor. Concrete is about a year old and relatively clean. Looking at the Legacy HD 39. Any one have any experience with this product?

Wood bleach or oxalic acid will clean the rust off. Paste wax after

30x40 is what I did doors on the 40 2 10x9. With my F150 4 door with 6.5 bed there is plenty of room to get around the truck. But if I had to do it again I would have gone 32 wide.

I used a bakers rack on my 10ft ceiling which I just finished last night. You will find that .750 emt slips right into the uprights, I drilled holes in the emt and could adjust to a different heights. Combined with two dead mans I was able to handle the 20' panels myself. .250 cordless impact...

I am getting ready to insulate the ceiling in my pole barn. It is 30x40x10 with attic truss and the floor for the attic has already been installed so blow in insulation is out. I was planning on going with R30 faced. If I go with faced insulation do I need to put a vapor barrier on the lower...

I think I will go with batts, then plastic.

I am going to insulate the attic floor. Bottom cords are 2x10 and the floor is installed. Attic floor ends about 8' from the wall. Just trying insulate the ceiling, roof has double bubble insulation on it. Not really worried about the temperature in the attic space.

The trusses are on 24" centers

I am in the process of finishing the inside of my pole barn which is 30x40 with attic truss. It will probably be next year before I can install the ceiling which is going to be steel. I was thinking of putting up plastic on the bottom of the trusses and blowing the insulation on top of the...

I am working the show stop by the Wheelabrator booth and ask for Rob. Working today seems to be a pretty good turnout.

Well thanks for the replies been busy running wire. A friend that is an electrician stop by and gave me some guidance. He said I was way over thinking this. He had some #1 copper and said that this would be fine for what I am going to be doing in the shop and I could have the wire. (I get him a...

This is a good point not sure it will fit I will check today. Like the wizard says I could run #2 to a J-box an splice.