Search results

Still available.

SOLD Wright 3/4" Drive 42" long 45 tooth ratchet. Part number 6425. Made in the USA. Used it a few times. In good working condition. A few scuffs and scratches from use. No previous owner engravings or markings. $160.00 + shipping (Probably $25ish) Paypal goods and services. PM if...

SOLD Proto 1/2" drive 6 point SAE 3/8" - 1-1/2" shallow and deep impact sockets. Made in the USA. 38 sockets total. Includes the following sockets - J74106 Shallow socket set - 3/8" 7412H 7/16" 7414H 1/2" 7416H 9/16" 7418H 5/8" 7420H 11/16" 7422H 3/4" 7424H 13/16" 7426H 7/8" 7428H...

SOLD Armstrong 1/2" drive metric and SAE pinless swivel impact socket sets. Made in the USA. 23 pieces total. Includes the following sockets - Metric set 47-913 - 10mm 47-110 11mm 47-111 12mm 47-112 13mm 47-113 14mm 47-114 15mm 47-115 16mm 47-116 17mm 47-117 18mm 47-118 19mm...

Stay off the Snap-on truck.

Updated, still looking.

Picked up the 4 ton Daytona jack from HF, but forgot to take the coupon for the freebie.

Anybody recognize this vise? No identification on it anywhere I can tell. It seems reasonably well made. Jaws are 6-3/8" wide. The mounting holes are a 6-1/2" x 10-1/2" rectangle.

I have a 1-11/16" and 1-7/8" socket in 1/2" drive made by Sunex. I've used them on drive shaft yoke nuts on big trucks. I want to say some of the nuts were in the 900 lbft range and so the Milwaukee 1/2" drive high torque handled them fine. For my uses, the 1-11/16" replaced a 3/4" drive...

A hair over 21"

Got my cart today. Wasn't on a pallet, just sorta poorly wrapped in some shrink wrap that didn't keep the edge of the handle from rubbing against the one next to it or the side of the trailer or something. No big deal, it saves me the angst of doing the "first damage." The bottom mat insert...

Thanks.

I do recall Midland Forge, but I didn't know they were part of CM. Thanks for all the replies!

I have some of these screw pin shackles with a mark I'm unfamiliar with. The "M" inside of a circle. I can't seem to find anything online - or can't search correctly. Does anyone know who the manufacturer of this shackle is?

I wasn't able to find it in the searching I did, but does anyone here know if there is a quick release anvil kit for the Snap-on TM70 1/4" drive ratchets? I'm not familiar enough with the pre dual 80 ratchets to know what the nomenclature of the quick release ratchets in that era were. This...

https://www.astrotools.com/product/42-piece-1-4-drive-low-profile-nano-impact-bit-socket-set/ This looks like something I'd be interested in.

Sold

I may try to straighten them, I suppose taking them off the trailer has to be done no matter what. The trailer itself does have support legs. They're not on the ramps, but under the dovetail.

They were bent when I got the trailer. I'd imagine someone put something too heavy over the ramps. There's some kind of spring retainer or something in there. I'm not certain how the springs and that are supposed to be arranged. Here's a photo of another one of the same trailer with the...

I have a 10 ton equipment trailer that needs new ramp pivot pins. The current ones are bent and greatly impede use of the trailer. Other than that they're steel, I don't know what they're made of. They are 2" diameter solid round bar that's about 37" long, with a washer welded to one end and...