Search results

I will agree with you 100% I'll go back and tell him to take additional photos and add to his listing. Bill I appreciate you chiming in. What was it that General Douglas MacArthur once said, "I Shall Return"

There is a member in a group I belong to who purchased this set of wrenches ten years ago for $350 and he currently has them listed on eBay. RARE USA VV CODE Vintage Craftsman 7peice deep offset box end wrench set #944328...

I went to a estate sale

General Geoff Thanks for responding, I had my house rewired for my Miller welder. will the Harbor Freight 60 gal. 5 HP 165 PSI Two Stage Air Compressor Item #93274 Run on 220V? Do I need a special plug? Thanks

I'm looking for information regarding the quality or lack of for the Harbor Freight 60 gal. 5 HP 165 PSI Two Stage Air Compressor Item #62299 Only: $799.99 Harbor Freight 60 gal. 5 HP 165 PSI Two Stage Air Compressor Item #93274 Only: $799.99 Rated 4.26 out of 5...

woodturner9, you mentioned that a dryer is a dual voltage device and uses 120 and 220 VAC. Typical dryer connection is two hots and a neutral - for the welder, you want two hots and a ground and if I have a four prong dryer receptacle, I might be able to make it work, but it is still not to code...

I couldn't find anything in the way of price that came close to it . I hope i'm not disappointed in my decision and it does every thing I need it to do. Kudos to you BD1 for giving me the heads up to this great deal and sberry for confirming it and to all others who chimed in. I can tell you...

Will the Miller 180 plug into my dryer or will I have to make an adapter cord? You've all been great with your responses, Thanks. One more thing the distance from my dryer to my wagon is approximately 45 Feet will this present any problems? sberry what do you mean: Its a poor substitute for...

Do you own either of these particular welders? the 190 is around $750 and the 210 seems to be around $950

I could use some help picking the right mig welder. I would like not to go over $700, I would like to plug in to my 220v dryer plug. I need a welder for replacing the 18 gauge floor pans and installing a MII front suspension and so on. I doubt if I will use it for anything else other than for...

Thanks for your comments, you have convinced me not to purchase a flux core welder. Even though my wagon won't be a show car, I still don't want it to look like a piece of s**t. Now that we have that out of the way what small inexpensive welder will do the job of welding the things I mentioned...

I'm trying to restore my 51 Chevy wagon, and I need to replace the floor pans and install a MII IFS front suspension along with a rear springs & bracket kit and along with other misc. welding. Can I use the Eastwood 90A Flux Core Welder. This will most likely be all the welding i'll ever do. I...

Can someone tell me what the letter O on the shank of a vintage ratchet is for. I believe the ratchet was made by Moore Drop Forging, It has the =V= mark. I'm not allowed to post pictures because I haven't enough postings yet, but you can see the ratchet in question here...

This one's for mjozefow, You show two boxes in one pic. a smaller one on top of a longer one, the one on the top is the one I just bought three of. I just posted a question on the forum "To Rivet Or Not To Rivet, That Is My Question" I'm looking for the smooth head rivets that craftsman used on...

Does anyone have a source for the smooth head rivets that Craftsman used on their small carry toolboxes? I purchased three boxes from the 40s-50s and I would like to do a great job on them by removing all the hardware instead of taping them before painting. I have seen some boxes that were...

Well I took apart the Indestro 3/8 Drive #6272 Ratchet. I was able to wiggle the selector lever off then I removed the pawl and low and behold there was nothing there. I did see a small hole in the side that has the handle and guess what I found, the ball bearing. Now PowderKeg said the ball...

Thank you for responding. I have the spring, could the ball bearing still be under the pawl? How do you remove the Pawl from the lever?

Hello Everyone I found an Indestro 3/8 Drive #6272 Ratchet in the wheel well of my 51 Chevy wagon when I bought it, well the selector lever wouldn't stay put in either right or left position so removed the two screws and removed the cover plate and out popped the spring. I was expecting to see a...

Hello Everyone Does anyone here at The Garage Journal know of or collect hand tools made by Bog Mfg. Co. or have information other than what is found here? https://home.comcast.net/~alloy-artifacts/bog-mfg-chicago.html I own a set of 1/2" sockets and this wrench shown here Fig. 32. Bog 5/8...

This is my 2nd post, the 1st was in the wrong forum and the guys told me to post my question here. I have several vintage Craftsman ratchets (30s & 40s) along with other manufactures that I have purchased without the detent ball and I wondered if someone had a source for them. I live in a little...