To avoid these ads, REGISTER NOW!

Cincinnati Tool Co.

P

Private Lugnutz

Well-known member
Joined
Mar 30, 2012
Messages
30,467
Location
The Authentic Jersey Shore
As I was saying on the the Bonney thread and the Tappet Wrenches threads, I recently traded a Milwaukee Tool & Forge 3-drawer chest to fellow GJer @Steven 33. In exchange, I got a bunch of cool miscellaneous stuff, including a Bonney "RAYTHEON" wrench, Keen Kutter tappet wrenches, and this wrench made for the Cincinnati Tool Company, which never met an abbreviation ("CIN'TI TOOL CO.") it didn't like! :) This had to be used to adjust something on one of its products. If anyone knows or has any good guesses, I'm all ears.
 

Attachments

  • 20240514_083253.jpg
    20240514_083253.jpg
    2.6 MB · Views: 55
To avoid these ads, REGISTER NOW!
A

AntiqueBen

Well-known member
Joined
Aug 4, 2021
Messages
1,438
Here's a heavy 8" clamp made by Cincinnati Tool Co. I have two of these & one I misplaced & I just recently found it. It's been missing for a long while, so it was severely rusted. This is a good example of why I like old tools. The old steel cleans up so nice. Before & after pics below. That's why I don't look over rusty tools out in the wild. As long as it's not severely pitted, there's a good chance it can look new again. Sometimes you have to see the beauty below the rust 😉
 

Attachments

  • IMG_20240517_182752751.jpg
    IMG_20240517_182752751.jpg
    1.1 MB · Views: 33
  • IMG_20240517_185932895.jpg
    IMG_20240517_185932895.jpg
    961.7 KB · Views: 22
  • IMG_20240517_190255863.jpg
    IMG_20240517_190255863.jpg
    1.1 MB · Views: 22
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
Private Lugnutz said:
As I was saying on the the Bonney thread and the Tappet Wrenches threads, I recently traded a Milwaukee Tool & Forge 3-drawer chest to fellow GJer @Steven 33. In exchange, I got a bunch of cool miscellaneous stuff, including a Bonney "RAYTHEON" wrench, Keen Kutter tappet wrenches, and this wrench made for the Cincinnati Tool Company, which never met an abbreviation ("CIN'TI TOOL CO.") it didn't like! :) This had to be used to adjust something on one of its products. If anyone knows or has any good guesses, I'm all ears.
Click to expand...
I don't see the circle H mark and the font of the stamp looks like the stamp on a couple of pre-Hargrave spokeshave blades I have. So that would probably put it before the 1920's. Unless the circle H is on the other side lol. I didn't find anything like it in the catalogs.

Mr Hargrave had the patent for the spring clamp and a bunch of other types of clamps. He liked putting his name on everything they made, eventually changed the name of the company to Hargrave.
 
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
P

Private Lugnutz

Well-known member
Joined
Mar 30, 2012
Messages
30,467
Location
The Authentic Jersey Shore
ararat said:
I don't see the circle H mark and the font of the stamp looks like the stamp on a couple of pre-Hargrave spokeshave blades I have. So that would probably put it before the 1920's. Unless the circle H is on the other side lol.
Click to expand...
No markings on the flip side. The branding is exactly the same as the branding on the Cincinnati Tool Co wooden clamps I have, which also have a second line ("CIN'TI, O., U.S.A").
ararat said:
I didn't find anything like it in the catalogs.
Click to expand...
I am guessing the reason it might not show up in catalogs is because it wasn't for sale as a separate item. As I alluded to above, it looks to me like something that would've come with something else. I have an Armstrong, for example, for adjusting the square nuts on a pipe wrench. I just don't know enough about Cincy/Hargrave to even speculate about what that might be. I was hoping someone like you would.
 
R

RTM

Well-known member
Joined
May 13, 2019
Messages
13,061
Location
SF Bay Area
Private Lugnutz said:
I just don't know enough about Cincy/Hargrave to even speculate about what that might be. I was hoping someone like you would.
Click to expand...
I flipped thru a couple of vintage catalogs, and didn't see anything likely. I wonder if it's from newer, post 50s stuff, where I don't look as often .

This is the only unusual thing to be, a hammer adapter, but I don't see a place to need a nut, or square fitting.

archive.org

The Cincinnati Tool Co. : Hargrave Tested Tools : General Catalog No. 80 : The Cincinnati Tool Co. : Free Download, Borrow, and Streaming : Internet Archive

56 p., illus., 27.5 cm, trade catalog
archive.org
 
Last edited:
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
Private Lugnutz said:
No markings on the flip side. The branding is exactly the same as the branding on the Cincinnati Tool Co wooden clamps I have, which also have a second line ("CIN'TI, O., U.S.A").

I am guessing the reason it might not show up in catalogs is because it wasn't for sale as a separate item. As I alluded to above, it looks to me like something that would've come with something else. I have an Armstrong, for example, for adjusting the square nuts on a pipe wrench. I just don't know enough about Cincy/Hargrave to even speculate about what that might be. I was hoping someone like you would.
Click to expand...
Yeah, I was looking for individual tools and machines that it might go with. The column clamp has a bigger wrench that goes with it. Not a lot of info out there for Cincinnati Tool Company. One day I'll post my clamp collection I acquired from a local estate sale a few years ago.
 
L

Leviton

Well-known member
Joined
Feb 25, 2019
Messages
894
Location
Oregon
This little clamp caught my eye due to the interesting screw handle, so I plopped down a dollar for it. Turns out, the handle is actually a patented feature by Mr. Hargrave.

From the patent:
"In the manipulation of a clamping screw there are two phases of move- The first phase may be designated as the approach movement and the second phase as the actual clamping or pressure applying movement.​

In the first named movement it is desirable to be able to manipulate the screw for quick rotation or rapid adjustment, whereas in the second named movement, speed of rotation is less important, the prime consideration being the ability to apply relatively great pressure manually or through the use of a wrench."​

The patent was granted in 1934. In the 1940 Cincinnati Tool Co catalog they advertised it as the new “Speed-Grip” thumb nut. The funny thing is, in the 1948 catalog they still touted it as being “New” (and mentioned that it combined “Speed with Power”).

Marking: CIN. TOOL Co (H) - 1-1/2 In No 571 PAT.AP.FOR C.T.CO. (with a small amount of the original red paint remaining).

Hargrave-CTCo Speed-Grip Pat.jpg
 

Attachments

  • C T Co 1948 catalog.jpg
    C T Co 1948 catalog.jpg
    677.2 KB · Views: 9
  • C T Co 1940 catalog.jpg
    C T Co 1940 catalog.jpg
    433.9 KB · Views: 10
  • CTCo Junior Clamp - Speed-Grip.jpg
    CTCo Junior Clamp - Speed-Grip.jpg
    1.5 MB · Views: 10
  • CTCo Junior Clamp - back.jpg
    CTCo Junior Clamp - back.jpg
    3.8 MB · Views: 8
  • CTCo Junior Clamp - front.jpg
    CTCo Junior Clamp - front.jpg
    3.9 MB · Views: 13
6

682bear

Well-known member
Joined
May 20, 2024
Messages
223
Location
West GA
I just picked up two clamps at a yard sale... they are both Cincinnati Tool / Hargrave No. 43... one is 6", the other is 8"...

20250315_202901.jpg

20250315_202931.jpg

20250315_202944.jpg

-Bear
 
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
To avoid these ads, REGISTER NOW!
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
d42jeep said:
I did some work on the clamp today with hand wire brushes and steel wool. It didn’t feel like it would be right to use evaporust on this clamp.IMG_1974.jpegIMG_1976.jpegIMG_1980.jpegIMG_1981.jpeg
-Don
Click to expand...
Very nice. I have a similar set of 4. Mine have 620250420_210551.jpg20250420_210605.jpg stamped on the bar, where your clamp has 8. Must be the size. They have a rivet at the end to keep the sliding jaw on there. 20250420_210615.jpg
 
D

d42jeep

Well-known member
Joined
Oct 22, 2014
Messages
16,484
Location
Northern California
I found two more little Cincinnati Tool Co clamps at yesterday’s estate sale. They spent the night in the evaporust. IMG_2067.jpegIMG_2068.jpeg
Here they are cleaned up. IMG_2113.jpegIMG_2114.jpegIMG_2115.jpegIMG_2116.jpeg
All the clamps together.
IMG_2117.jpeg
Found a couple more in the clamp drawer.IMG_2126.jpeg
-Don
 
Last edited:
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
I've had it for a couple of years, just haven't gotten around to cleaning it up yet. The clamp body has been half repainted and the red base is just dirty. I think I'll repaint the silver and just clean the red parts.
 
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
So, from the catalog image above it's the junior clamps that go on it. Not the super junior clamps. Luckily I had 3 No 549 clamps to put on there. Unfortunately I need to find the other clamps in the set. Lol. My clamps have cooler handles than the ones pictured.

So, I started wire wheeling the silver paint off and it got shinier. Pretty sure it is cad plated, so I won't need to take any cadmium supplements this week.

I finished cleaning it with wd40 and steel wool. Cleaned the red parts and gave them a light coat of BLO. The 549s look pretty good on there I think.
20250427_172513.jpg20250427_172541.jpg
 
P

Private Lugnutz

Well-known member
Joined
Mar 30, 2012
Messages
30,467
Location
The Authentic Jersey Shore
Looks terrific.

I want one! Realizing that the odds of finding one are slim, my thoughts have turned to fabrication. Fairly easy, and the stand could even be something more amenable to holding a standard clamp upright without a post. The idea of an extra large clamp as a stand for smaller clamps of the same brand, and any brand, has a grip, pun fully intended, on the Curator in me now. It just looks friggin' cool.
 
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
Private Lugnutz said:
Looks terrific.

I want one! Realizing that the odds of finding one are slim, my thoughts have turned to fabrication. Fairly easy, and the stand could even be something more amenable to holding a standard clamp upright without a post. The idea of an extra large clamp as a stand for smaller clamps of the same brand, and any brand, has a grip, pun fully intended, on the Curator in me now. It just looks friggin' cool.
Click to expand...
I have only seen one other and it was missing the base. This is a 6" standard clamp. There is a screw holding the base on. The bottom of the clamp part that is tapped for the screw looks like it is cast with the clamp, but you could weld a nut to the bottom and add a base if you wanted to fabricate one.20250427_184353.jpg
 
A

ararat

Well-known member
Joined
Dec 27, 2018
Messages
578
Location
Ararat NC
I have the 549s in the picture, a 548 that I am painting because it is a different shade of red, and I just ordered a 570. I don't have any of the other junior clamps listed above.

I found a can of spray paint that is a match for the red, I am pretty sure it was here when we moved in. Somehow it still works.

I would be interested in any of the others you might have. I want to get one of each.
 
  • Like
Reactions: RTM
C

Car hobby

Well-known member
Joined
Nov 9, 2012
Messages
75
Location
DFW,Texas
Here are three Cincinnati Tool Company C Clamps that I restored not to long ago. I found just enough paint on them to repaint them their original color. The screws work great. I can't remember if these were my father's or where I got them. Cincinnati Tool Co C Clamp.jpeg
 
You must log in or register to reply here.
To avoid these ads, REGISTER NOW!
Top Bottom