Beerhippie
Well-known member
Nice kids.
Hammer time!
- Thread starter Outlawmws
- Start date
four.cycle
Well-known member
"Vidar North" and "Vidar South" are two peaks in the Valhallas - located on the divide between the Queets and the South Fork of the Hoh.
four.cycle
Well-known member
Sorry... took me a while to remember where the photo was... finally found it:
L to R: Sleipner, Vidar South, Vidar North, Munin, Woden (from mouth of Hee Hee Creek) 09/14/02 BK
Sorry that image is so small... I should re-scan some of these shots.
L to R: Sleipner, Vidar South, Vidar North, Munin, Woden (from mouth of Hee Hee Creek) 09/14/02 BK
Sorry that image is so small... I should re-scan some of these shots.
Eric Brown
ALLIANCE MEMBER
- Joined
- Jun 14, 2024
- Messages
- 715
Hammer I just bought new from Union Manufacturing Company for adjusting plane blades. Very nicely done. I think they are closing out production on these so if you want one, now is the time.
four.cycle
Well-known member
^ That looks pretty serious there, Eric.
Eric Brown
ALLIANCE MEMBER
- Joined
- Jun 14, 2024
- Messages
- 715
Hammer I just bought new from Union Manufacturing Company for adjusting plane blades. Very nicely done. I think they are closing out production on these so if you want one, now is the time.
It doesn't take much to move a plane blade. A light tap. This one is well made. Soft steel to reduce any damage and yet heavier than the ones with plastic or wood tips. Brass would have been good too, but more expensive.^ That looks pretty serious there, Eric.
coachwash
Well-known member
Beerhippie
Well-known member
Utica? Early logo was interlocking links like that.
If the three ovals were on pliers, I wouldn’t hesitate to say Utica, pre-1912. But I don’t think Utica made hammer heads. I DO have a hammer somewhere with similar three ovals on it, but concluded they were hand struck with an O or 0.
The nonstandard proportions for a ballpein, and embellishment of the double encircling rings makes me think may be non-USA and/or pre-20th century.
The nonstandard proportions for a ballpein, and embellishment of the double encircling rings makes me think may be non-USA and/or pre-20th century.
four.cycle
Well-known member
Esting "Safe-T-Shape" claw hammer 07/18/26
genog
Well-known member
I found a little 2 oz Paschall BP at the HS Flea Market today
Hilariously cute
Hilariously cute
Beerhippie
Well-known member
Here's my smallest BPH compared to my 2 oz Stanley:Hilariously cute
Bought solely because it was hilariously cute. The 2 oz actually sees a fair amount of use, but the 1 oz is pretty much a wall-hanger.
NoahG
Well-known member
Work buddy grabbed this for me the other day
KnurledNut
Well-known member
Those handles like to break right at the head. I would go easy with any pulling and prying. Thanks for sharing.Work buddy grabbed this for me the other day
Beerhippie
Well-known member
You don't pull or pry with an axe-handle framer. If you have to, you do it sideways.
georgiadave
Well-known member
I would not pry with that handle. Also, buy handles that have the grain perpendicular to the strike/pull axis and running the length of the handle.
KnurledNut
Well-known member
I used a cali framer daily for many years building homes and later doing commercial construction. It doesn’t take long to learn the limitations of wood handled hammers.
Beerhippie
Well-known member
That's why I--and many others--kept an Estwing Blue Bomber on hand. Full length stand-up framer w/ripping claws, solid steel. Wouldn't want to drive nails with it all day, but great for demo work. The Hart framer was for driving nails.
The Estwing is still in my carpentry bucket at the shop, as there's no way anyone can damage it. Hart framers are retired to a place of honor on the wall.
KnurledNut
Well-known member
Oh yeah...I'm well aware. I bought a Big Blue brand new and after using it on one build I was done with it. Way to much hammer for regular use. It did get used hard though and they are certainly tough. I ran Estwings for years starting out due to well-intentioned advice, but I eventually learned that wood was the way to go.
Here's an old picture of a few of the Estwings I carried. Big Blue is dead center. Most of these hammers have helped build at least one house back when they were my daily drivers. My favorite was probably the one with the hammertooth just to the right of Big Blue. I think it was a 24oz. That one got quite a few miles doing concrete form work too. The red one is the first generation Estwing released with a wood handle. I didn't really care much for the head geometry so after the original handle broke and I replaced it with the one pictured, switched to Vaughan and used them ever since.
I still have my original Hart Decker but never tried the Framer.
The roofing hammers eventually got replaced with wood handle AJC Mag-hatch.
My wrist and elbow have thanked me for moving on.
Estwings are durable but I have seen claws break off, heads chip, shafts bend and grips split.
This stouthearted Vaughan is what I currently use and has been with me for many years. I painted the head Chevy orange at one point in its life. One of the best framers ever made IMO:
I liked these so much I bought a new one, rehandled it with my choice of grain and color and mirror polished it with full intentions of making it too nice to use.
Last edited:
Beerhippie
Well-known member
A few of my Estwings:
Blue Bomb, bottom, was also used for a year or so until I figured out why I was the only guy on the site using a steel-handle hammer. Roofer had many years and acres of roof under it. Cord wrap on the grips was from working in the rain and snow--much easier to keep a solid grip than rubber (vinyl?).
My Harts, after a clean-up and buff:
I used those for some twenty years off and on.
Now retired:
The little, smooth-face framer" was my trim and finish hammer. 25 oz Cali axe-handle--Ol' Two-Swat--was my daily driver for most of the time I spent cutting boards and driving nails.
Blue Bomb, bottom, was also used for a year or so until I figured out why I was the only guy on the site using a steel-handle hammer. Roofer had many years and acres of roof under it. Cord wrap on the grips was from working in the rain and snow--much easier to keep a solid grip than rubber (vinyl?).
My Harts, after a clean-up and buff:
I used those for some twenty years off and on.
Now retired:
The little, smooth-face framer" was my trim and finish hammer. 25 oz Cali axe-handle--Ol' Two-Swat--was my daily driver for most of the time I spent cutting boards and driving nails.
KnurledNut
Well-known member
Oh yes, I see what hammer you are referring to now that I see your picture. That one had a standard pattern Estwing head with a extra long handle. I thought you meant the one they actually call Big Blue that has a very distinct california framer head on an extra long handle, as I pictured above. Both beast mode hammers!
Beerhippie
Well-known member
I don't think Blue Bomb was any kind of official name--just what everyone on the jobsite called them--probably because they were mostly used for demo work and stripping forms.
fishwatcher
Well-known member
- Joined
- Jan 26, 2023
- Messages
- 766
I picked up an old Craftsman hammer and rubber mallet for $15 at the flea market.
Both handles have been cleaned and sanded lightly from the original, worn finish.
Boiled Linseed oil alone made it too light.
I tried to wipe off the BLO with mineral spirits and added some Minwax stain to darken it.
Finally, after wiping down the stain and a day and a half to cure, I wiped them down again with boiled linseed oil.
They now fit nicely on my mostly Craftsman hammer rack.
Both handles have been cleaned and sanded lightly from the original, worn finish.
Boiled Linseed oil alone made it too light.
I tried to wipe off the BLO with mineral spirits and added some Minwax stain to darken it.
Finally, after wiping down the stain and a day and a half to cure, I wiped them down again with boiled linseed oil.
They now fit nicely on my mostly Craftsman hammer rack.
Last edited:
Pretty sure this won't be found in any catalog.
It's larger than it looks. It's a foot and a half long and weighs 6.8 pounds. The head is solid lead. The steel shank runs clear to the polished steel **** piece. The handle is stacked polymer layers of different types and colors that have been contoured with grooves.
It's larger than it looks. It's a foot and a half long and weighs 6.8 pounds. The head is solid lead. The steel shank runs clear to the polished steel **** piece. The handle is stacked polymer layers of different types and colors that have been contoured with grooves.
Attachments
Beerhippie
Well-known member
Serious '70s high-school shop project vibes.Pretty sure this won't be found in any catalog.
It's larger than it looks. It's a foot and a half long and weighs 6.8 pounds. The head is solid lead. The steel shank runs clear to the polished steel **** piece. The handle is stacked polymer layers of different types and colors that have been contoured with grooves.