To avoid these ads, REGISTER NOW!

Above 1200 Sq/FT Harley Jim's place

Wokspaces above 1200 squarefeet.
To avoid these ads, REGISTER NOW!
OP
H

harley jim

Well-known member
Joined
Dec 6, 2013
Messages
11,404
Location
Cleveland Tn..........out in the sticks
They just tossed it up there. I wasn't there but I would guess there were 4 or 5 men on that hunt. Bear hunting is a group event where each man brings his best dogs, there are bragging rights and such at stake. I'm sure they were from different states also, Josh hunts in many states from Louisiana to the Carolinas and they are all just friends.
20221115_102212.jpg
It's also a family event, the family's often go along, Whitley is four and loves Bear hunting, you just live different here.
 
Last edited:
OP
H

harley jim

Well-known member
Joined
Dec 6, 2013
Messages
11,404
Location
Cleveland Tn..........out in the sticks
I checked out the doors and drawers and they needed a third coat so I painted again, worst paint ever or worst painter ever, I'm not sure.
20231116_115053.jpg
Going to Southeastern Salvage in a few minutes to get the counter top.

20231116_110116.jpg
I had a blowout this morning.
20231116_110103.jpg
I cut me a couple of toe boards.
20231116_110131.jpg
Insert, remember TGIF,
20231116_115013.jpg
Some Gorilla glue and 24 hours, be good as new!
I did run my Drexel tool around inside to clean the surfaces.
I will be glad to get this porch job finished, there is too much wait time between coats and I do silly stuff like this while I wait!
 
OP
H

harley jim

Well-known member
Joined
Dec 6, 2013
Messages
11,404
Location
Cleveland Tn..........out in the sticks
I like your Rat Fink sign. Is there a story on that?
I won it at a car show this summer, RF was my hero when I was young, heck! He still is.

Mack, we don't need no stinkin cobblers. Lol.

Terry, I will find some of that, the Gorilla glue only lasted about two months last time.

Shorty, I got a pair but they had a blow out last year and I haven't fixed them yet, I gotta get busy!

I made it to Southeastern Salvage and got the counter top, we have cut it to fit and cut a backslash and toe kick also. Hoping to have it finished tomorrow.
 
To avoid these ads, REGISTER NOW!
OP
H

harley jim

Well-known member
Joined
Dec 6, 2013
Messages
11,404
Location
Cleveland Tn..........out in the sticks
What time is dinner? Looks like a great place to break bread.
Whenever you stop in, there's always something to eat here!
Pat and Trish will start cooking Wednesday, they usually cook all night, then Trish will load her car and drive to our place about 8:00 am and they will finish off everything so we can eat about 2:00, and4:00, and6:00 and so on!
 
OP
H

harley jim

Well-known member
Joined
Dec 6, 2013
Messages
11,404
Location
Cleveland Tn..........out in the sticks
Got to play in the shop a little yesterday.
20231124_160735.jpg
I need a new welding roller, I have these flange bearings.
20231124_161744.jpg
I cut the cages and rubber isolators off.
20231124_170904.jpg
I cut two pieces of ½" conduit 24" and welded them to two pieces of angle iron 4½" long.
20231124_170931.jpg
The bearings will slide on the conduit to adjust the length and the tank will roll very easily, works great for tig welding.
 
To avoid these ads, REGISTER NOW!
Top Bottom