HOT DEAL Index!!
- Thread starter Stuey
- Start date
- Status
Looks like a door mat, flat on the bottom with rubber pegs sticking up.
Working on a hard floor like concrete gives some people trouble with their legs. Cushion sole shoes, or rubber mats at places where you stand a lot can help.
Working on a hard floor like concrete gives some people trouble with their legs. Cushion sole shoes, or rubber mats at places where you stand a lot can help.
I'm surprised nobody has mentioned Home Depot SPRING black friday, or has it already?
they have a 9 gal, 3.5hp Ridgid shop vac for $20 (the one that came out on the real black friday was 16 gal, 5hp).
Anyway, it started 3/18 and they have some other stuff on sale
http://www6.homedepot.com/savingsevent/index.html
(not sure if link works)
they have a 9 gal, 3.5hp Ridgid shop vac for $20 (the one that came out on the real black friday was 16 gal, 5hp).
Anyway, it started 3/18 and they have some other stuff on sale
http://www6.homedepot.com/savingsevent/index.html
(not sure if link works)
Last edited:
I can't really open the link. Everything I do is on my phone and when I go to sears its sends me the 'sears2go.com' which is the mobile friendly version or their site.
I am wondering if the coupon or link you listed above would allow me to get 10% off of sears 'deal of the day' the rolling cabinet for $72 or if that is calculated in to that. Cause when I open the page to the cabinet it shows it as $80.
Which either way seems like a good deal, but I am curious if I could score another 10% off of that $72.
billymade
Well-known member
Snapon has a new trade in promotion on tool box upgrades; $1000 minimum:
http://www.snapon.com/1000bucks/
http://www.snapon.com/1000bucks/
alohavw
Well-known member
Anyone that has a HF Tool Box or the HF 5 drawer Tool Cart, they have a close out sale on the 2 shelf end cabinet for 69.99 plus an additional 20% off using the coupon.
Here is the one on close out.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=67436
And here is the one I use it with.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=95272
Here is the one on close out.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=67436
And here is the one I use it with.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=95272
Is that at all hf's? Where are you located in WA?
alohavw
Well-known member
Purchased at the Kent,WA store and they said that it went on close out at all HF stores. You might have to call and confirm as it wasn't in their system yet so have them check the price tag on the product. Hope that helps.
I got an email coupon for this today for $139
http://www.harborfreightusa.com/usa/itemdisplay/displayItem.do?itemid=67421
A three box set - I don't know if they are any good or not
tool box # 67421 - regular $299
http://www.harborfreightusa.com/usa/itemdisplay/displayItem.do?itemid=67421
A three box set - I don't know if they are any good or not
tool box # 67421 - regular $299
Found the mother load of coupons from Harbor Freight
http://www.harborfreightusa.com/html/SingleMagLanders/
click on one of the magazine folders and pick the html format and your good
http://www.harborfreightusa.com/html/SingleMagLanders/
click on one of the magazine folders and pick the html format and your good
I went to HF today looking to get a few of these. They didn't know anything about the closeout and the price was $149.99. I came home empty.
alohavw
Well-known member
The HF manager that did the price adjustment told me that it was on close out system wide. My father in-law got the same deal today at a different HF. Oh well, sorry about the inconvience.
Last edited:
anyone else have any luck with this?? I would really like to get one of these.
fsrtwo
Member
What model saw do you have to buy to get the stand free?
u can get a 40" , 22 drawer combo , for $629,
UncleJoe
Well-known member
Harbor Freight 580 pound capacity 4 drawer roller cart $99 with email coupon. PM me if you need the coupon. Coupon good till 4/4/2010 but they show up a lot
I have this and use it to hold my welding tools. I mounted a cheap old side box to it and my welder sits on top of the side box. For the money it works just fine for a hobby box.
I have this and use it to hold my welding tools. I mounted a cheap old side box to it and my welder sits on top of the side box. For the money it works just fine for a hobby box.
Last edited:
Harbor Freight 580 pound capacity 4 drawer roller cart $99 with email coupon. PM me if you need the coupon. Coupon good till 4/4/2010 but they show up a lot
I have this and use it to hold my welding tools. I mounted a cheap old side box to it and my welder sits on top of the side box. For the money it works just fine for a hobby box.
*I have one of these. have had it for years and its the best cart I've owned. Quite ironic for HF
I have seen these carts in the store several times but have never seen the red 5 drawer in the store. Are they the same overall size? Is the red one better?
nolatoolguy
Banned
LOOKS pretty good if its what he sais it is.....basicly a mid level mechinics tools an tool storage
UncleJoe
Well-known member
I have both and the red one is a little bigger and holds more weight. Seems to be a little more robust.
shocksystems
Well-known member
Harbor Freight 580 pound capacity 4 drawer roller cart $99 with email coupon. PM me if you need the coupon. Coupon good till 4/4/2010 but they show up a lot
I have this and use it to hold my welding tools. I mounted a cheap old side box to it and my welder sits on top of the side box. For the money it works just fine for a hobby box.
UncleJoe: Can you post a picture of it with your modification? Thanks! Jim
UncleJoe
Well-known member
I will try to get a picture of it tomorrow.
IONH
Well-known member
Does it have ball bearing slides?Harbor Freight 580 pound capacity 4 drawer roller cart $99 with email coupon. PM me if you need the coupon. Coupon good till 4/4/2010 but they show up a lot
I have this and use it to hold my welding tools. I mounted a cheap old side box to it and my welder sits on top of the side box. For the money it works just fine for a hobby box.
UncleJoe
Well-known member
Reply for Shocksystem: here are some photos of the "side box" modification I did.
I had a 30 plus year old tool box and cabinet that I think I bought at Kmart. It was unusable as a tool chest. I took the wheels off and mounted the bottom on the wall as a cabinet. When I got the HF cart I wanted to place my welder on a side stand I saw the old cabinet hanging on the wall and figured it would work. A little sanding and some black paint and there you go. I saw the same cabinet at a flea market this weekend for $20
Also to answer the question by IONH the slides are ball bearing and very smooth under load. The detents (sp) were a little stiff and I will need to adjust them but I have not bothered with that yet.
I had a 30 plus year old tool box and cabinet that I think I bought at Kmart. It was unusable as a tool chest. I took the wheels off and mounted the bottom on the wall as a cabinet. When I got the HF cart I wanted to place my welder on a side stand I saw the old cabinet hanging on the wall and figured it would work. A little sanding and some black paint and there you go. I saw the same cabinet at a flea market this weekend for $20
Also to answer the question by IONH the slides are ball bearing and very smooth under load. The detents (sp) were a little stiff and I will need to adjust them but I have not bothered with that yet.
Last edited:
SocketDeviler
Well-known member
IONH
Well-known member
Wow, I really like that setup! I like how you basically made that a welding/grinding cart (minus the actual bench top grinder) which puts everything within reach with just one roll away.Reply for Shocksystem: here are some photos of the "side box" modification I did.
I had a 30 plus year old tool box and cabinet that I think I bought at Kmart. It was unusable as a tool chest. I took the wheels off and mounted the bottom on the wall as a cabinet. When I got the HF cart I wanted to place my welder on a side stand I saw the old cabinet hanging on the wall and figured it would work. A little sanding and some black paint and there you go. I saw the same cabinet at a flea market this weekend for $20
Also to answer the question by IONH the slides are ball bearing and very smooth under load. The detents (sp) were a little stiff and I will need to adjust them but I have not bothered with that yet.
UncleJoe
Well-known member
It sure is handy to have everything in one place when I need to do an metal fabrication. I am going to mount a pole up the back to hang my welding helmets and welding jacket and respirator and stuff. I have a heavy duty extension cord holder on the back side.
I will also weld a bar across the back to hold C-Clamps and stuff. Pretty much everything I need in one box.
I could not buy the casters, trim rails, handles and sheet metal and paint and build it myself for what I have in it now.
I will also weld a bar across the back to hold C-Clamps and stuff. Pretty much everything I need in one box.
I could not buy the casters, trim rails, handles and sheet metal and paint and build it myself for what I have in it now.
www.strictlytoolboxes.com has a special on their 72" Montezuma boxes for only $1745, free shipping. That's a killer deal if you ask me.
Direct Link
Direct Link
shocksystems
Well-known member
Reply for Shocksystem: here are some photos of the "side box" modification I did.
I had a 30 plus year old tool box and cabinet that I think I bought at Kmart. It was unusable as a tool chest. I took the wheels off and mounted the bottom on the wall as a cabinet. When I got the HF cart I wanted to place my welder on a side stand I saw the old cabinet hanging on the wall and figured it would work. A little sanding and some black paint and there you go. I saw the same cabinet at a flea market this weekend for $20
Also to answer the question by IONH the slides are ball bearing and very smooth under load. The detents (sp) were a little stiff and I will need to adjust them but I have not bothered with that yet.
UncleJoe: That is great! Gives me inspiration.
Cheers! JimQuick question, I have a similar roller cart, Sears, got as gift. I am finding it a bit odd to work with.
Top closed got working surface = cant use inside, top compartment.
Top open, = no working surface. Maybe I am getting old,
what do you guys do / how do you use the cart effectively?
Top closed got working surface = cant use inside, top compartment.
Top open, = no working surface. Maybe I am getting old,
what do you guys do / how do you use the cart effectively?
Last edited:
UncleJoe
Well-known member
I could be wrong but to me a roller cart is to hold the tools you need for the job at hand. It is not a work bench. Often a mechanic will have a lot of tools. He will take what he needs from his large box and load it on the cart and take that to the project. This way he does not have to strain trying to roll a large tool box across the shop. I think you need a work surface and a cart. I have an old craftsman "project center" box that had a work surface on the top and 5 drawers below. I used that for a while just like you are describing.
knobby
Well-known member
2 left not a bad deal
http://cgi.ebay.com/Armstrong-4-pie...emQQptZLH_DefaultDomain_0?hash=item2a051daa25
http://cgi.ebay.com/Armstrong-4-pie...emQQptZLH_DefaultDomain_0?hash=item2a051daa25
IONH
Well-known member
This is a key point to many DIY projects.
It often ends up costing more to have a full DIY project piecing bits together than it would to just buy an item which is close to handling what you want to accomplish and customizing it to satisfy what it is missing.Enloe
Well-known member
thanks Knobby I got the last one
metal1313
Well-known member
i have something to add, and to ask if they are decent bits.
enco has a set of machine screw length USA made drill bits for under 45. http://www.use-enco.com/CGI/INSRIT?cm_mmc=Email-_-033010-_-NA-_-Prospect&PMAKA=TB890-9242
theres also a code for free shipping on orders over $25.
enco has a set of machine screw length USA made drill bits for under 45. http://www.use-enco.com/CGI/INSRIT?cm_mmc=Email-_-033010-_-NA-_-Prospect&PMAKA=TB890-9242
theres also a code for free shipping on orders over $25.
Bolster
Well-known member
Anybody seen an ENCO free shipping code lately?
The last code for free shipping was WFSC3, but it expired on 3/26/10 .. should be another one coming soon ..
billymade
Well-known member
Latest deals from Gray Tools of Canada:
http://www.graytools.com/pdf/Professional Tools Special - Spring 2010 - EN.pdf
http://www.graytools.com/pdf/Professional Tools Special - Spring 2010 - EN.pdf
- Status