spoonsports86
Well-known member
started to organize my tool box finally and go figure i only get 2 drawers dont
Let's see your toolbox.
- Thread starter wythors
- Start date
Most recent. Taken today.
Sent from my SPH-L720 using Tapatalk
How do you like that Carlyle ratchet compared to your snap-on ratchets?
And…
How do you like that snap-on indexable ratchet?
FOCUS.FREAK
Well-known member
The caryle ratchets are nuce. As far as being smooth I'd have to go with the snap on. The snap on indexable ratchet is temporarily out of service. The gears are stripped. It's a buddy's at work I'm just warranting it.
Sent from my SPH-L720 using Tapatalk
upgrading
Well-known member
CANned-hAM
Member
- Joined
- Oct 1, 2013
- Messages
- 23
$3500 with some tools left in it.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
CANned-hAM
Member
- Joined
- Oct 1, 2013
- Messages
- 23
Previously loved. Only thing wrong with it is the missing mustang badges
Sent from my iPhone using Tapatalk
jakemac
Well-known member
Gas prices have really been killing me, figured it was time to upgrade. Hopefully this will help
HaHaHaHaHa ! Does your box smell like french fries now ?
AV tinker er
Well-known member
They are Taiwan, but a decent driver. I have a set in green.
Brownsfan
Well-known member
How is that box holding up? I am buying the 52" top and bottom soon and would like to hear your opinion on yours. Your box is on sale for 699 right now. I was considering it and the add on side box. But I like the 52" better
@Brownsfan
Honestly i do not like this craftsman box at all! The drawers are build so crappy! Thin metal!! Whenever I roll the box around the hanger the drawers bang around even when it is locked!! Thumbs down! I cant wait until my SO box comes!!
Honestly i do not like this craftsman box at all! The drawers are build so crappy! Thin metal!! Whenever I roll the box around the hanger the drawers bang around even when it is locked!! Thumbs down! I cant wait until my SO box comes!!
bodyguy16
Well-known member
My baby
Top drawer
Screwdriver drawer
Hammer drawer
Pneumatic drawer
Wrench drawer
Pliers drawer
Have quite a few more drawers but way too messy for pics lol
Thats a great box, i love mine.
silverdot1211
Well-known member
- Joined
- Feb 2, 2013
- Messages
- 45
wkderf
Well-known member
My turn:
I share some garage space with my housemates, but I take my workspace & toolbox more seriously than they do:
I share some garage space with my housemates, but I take my workspace & toolbox more seriously than they do:
Last edited:
ewils35
Well-known member
Very nice and neat. If y'all seen mine y'all would flip
Sent from my DROID RAZR HD using Tapatalk
Sent from my DROID RAZR HD using Tapatalk
JDSV
Well-known member
That foam looks very clean. What did you use to make the cuts?
wkderf
Well-known member
The foam is from Craftsman, and to cut the tools out I used an exacto knife, #11 blade specifically.
its very time consuming, but well worth it in the end. with every tool having a cutout, its easy to see if I'm missing a tool just by glancing at the open drawer.
Wrench drawer
Hey, what's the story with that hard handle box wrench?
devoncoolman
Well-known member
wkderf
Well-known member
yeah, the price was steep even for a single wrench, but I've done a bunch of nitrous & CO2 system installs, and the AN4 size is whats used most for those, so it was worth the price to have the right tool.
Here is mine.
Oh man that is just
That with the second side locker, or the Snap Epiq version with both lockers, is my dream toolbox.
I don't think I will ever have one, but do I love to dream
Please do post up a pic if you add the second side locker.
RedF
Well-known member
Here is mine.
Currently out grown. I am getting another locker, but that might not be enough. I DONT want another tool box payment though.
[/URL][/img]
That's sort of a strange design for a riser, does it close or lock in any fashion?
KRSC43
A fresh wax!
Ratchets so far. most used are put in with the sockets
Top compartment. Tune up and brakes tools. Little scanner that is awesome. Multimeter in black case on left (youll see it in my bottom drawer picture but I keep it here now). Speeders, ratchets, knives, and misc. stuff. Also keep my grandfathers 50's or 60's screwdrivers (red and black) in the middle for good luck.
Sockets (shallow, semi-deep, deep, and swivel in both 1/4 and 3/8. Hex bit 4-10 and torx t8-t55), extensions, and my most used ratchets. Adapters and universals as well.
Wrenches, 10-22, +24 In Flank Drive and 10-19 Ratcheting Flank Drive Plus. 60 offset. A couple Mac 0 offset, love em. Allen keys. And seal spoons and scrapers that I have no room to put anywhere else lol
Screwdrivers. Pretty straight forward. Got the minis layed out.
And how the drawer usually looks. Got new torx so I jus put them on top and slide them off what I need.
Pliers and clip tools in back
Black roll pouch on the right is this
Impacts, SN24 Breaker bar, hammer, punches, roll pin punches, radiator picks, and torque wrenches
Torque wrenches
Last drawer, Beginning of my diagnostic tools spread out. Compression gauge, coolant system tester, and multimeter. Black cased with red snap on is cts561 cordless screwdriver that I'm trading for the 661 lithium once my driver gets it in.
Same drawer with cases stacked on side like usual, and minus the coolant tester i usually lay on the 1/2 impacts.
Impact sockets. Shallow, deep, and swivel in 3/8 and 1/2
A fresh wax!
Ratchets so far. most used are put in with the sockets
Top compartment. Tune up and brakes tools. Little scanner that is awesome. Multimeter in black case on left (youll see it in my bottom drawer picture but I keep it here now). Speeders, ratchets, knives, and misc. stuff. Also keep my grandfathers 50's or 60's screwdrivers (red and black) in the middle for good luck.
Sockets (shallow, semi-deep, deep, and swivel in both 1/4 and 3/8. Hex bit 4-10 and torx t8-t55), extensions, and my most used ratchets. Adapters and universals as well.
Wrenches, 10-22, +24 In Flank Drive and 10-19 Ratcheting Flank Drive Plus. 60 offset. A couple Mac 0 offset, love em. Allen keys. And seal spoons and scrapers that I have no room to put anywhere else lol
Screwdrivers. Pretty straight forward. Got the minis layed out.
And how the drawer usually looks. Got new torx so I jus put them on top and slide them off what I need.
Pliers and clip tools in back
Black roll pouch on the right is this
Impacts, SN24 Breaker bar, hammer, punches, roll pin punches, radiator picks, and torque wrenches
Torque wrenches
Last drawer, Beginning of my diagnostic tools spread out. Compression gauge, coolant system tester, and multimeter. Black cased with red snap on is cts561 cordless screwdriver that I'm trading for the 661 lithium once my driver gets it in.
Same drawer with cases stacked on side like usual, and minus the coolant tester i usually lay on the 1/2 impacts.
Impact sockets. Shallow, deep, and swivel in 3/8 and 1/2
Last edited:
yogitech
Well-known member
Nice GREEN stuff!!!!
Most recent. Taken today.
Sent from my SPH-L720 using Tapatalk
What socket trays do you have on the far left of that drawer?
sent from android mobile
Mach5
Well-known member
Here's my main toolbox:
And here is what it replaced:
And here is what it replaced:
Nice GREEN stuff!!!!
Thank you!
Reality Sucks
Well-known member
- Joined
- Dec 16, 2010
- Messages
- 276
**Some drawers pictured are missing some tools, there were loaded on my cart that day. Ill get a pic of that to tomarrow.
What I generally do on a day to day basis..
What I generally do on a day to day basis..
Last edited:
Thanks guys for this thread, this is my current setup. 2 craftsman and a snap on tool cart.
Im planning on selling the two right boxes (snap on and crafstman) and picking up a single 44 in US general harbor freight special for right now, then grabbing a second one down the line. Space in my garage is at a premium so im opting for 2 lower profile boxes to make a small work bench.
Im planning on selling the two right boxes (snap on and crafstman) and picking up a single 44 in US general harbor freight special for right now, then grabbing a second one down the line. Space in my garage is at a premium so im opting for 2 lower profile boxes to make a small work bench.