not JAFO anymore

[i8tokyo]

So I have a question for you guys. Well kind of 2 questions.
first is quotes from contractors. I have had the hardest time getting people to get them to me then to take the damn job. Insulation guys are my ***** right now.
second is help. I can't get guys to call me back that are off right now. Well ones that are worth a damn.. Anyone else run into this?

 

[N0tt0N]

This place is MEGA! Watchin' & Wishin'! Congratulations and good job

 

[i8tokyo]

so this wall used to be lined with ****. feels good. so Now I have the auto part wired other then the alarm wires. Getting cold, almost to cold to work with thin gloves.

 

[i8tokyo]

So I had a visitor give me **** about my steps on my scaffolding. I like my steps. bets the hell out of climbing them normaly

 

[i8tokyo]

so i added a 10inch bazooka tube yesterday. sounds a bit better

 

[i8tokyo]

I need to get me one of these to catch the mice

 

[motofool33]

subscribed for updates lookin good so far like the pool too lots of hard work there

 

[i8tokyo]

I seriously tried to use the force for like 5 minutes to get the screw gun. Too lazy to climb down off the scaffolding

 

[i8tokyo]

I am feeling very dejected right now cause I have a low midiclorian count. Sux big time

 

[i8tokyo]

running air line. and before you flame me it is in the wall so no shards embedded in anyones chest

 

[i8tokyo]

so I extended the foam for the ridge vent and boxed in around where I had to raise the ceiling for my lift so I can blow cellulose insulation in and keep 12 inches then I framed the (bridge/catwalk) so I can get to the other end. started running it down the middle, started mistake 642 is what I did . Forgot about the chimney for the radiant heat hence the winding path

 

[i8tokyo]

So I am back. Been off for a while with a blown disk. 2 sets of 3 shots for that and a heart issue. Damn Afib. Going in to get my ticker burnt in about a month but I am rolling for a bit

 

[i8tokyo]

Sent from my SAMSUNG-SGH-I317 using Tapatalk

 

[i8tokyo]

Sorry ffor the double post . Still trying to figure or this app for the phone. Anyways this is my tool room. 3 HF tool boxes go on the shelf to the left and that is a vinyl flooring I am putting in. 6 lights switch so I can have 2 4 or all 6. The big wad or wires is all the speaker wire head end I built the corners out so I dont loose stuff in the corners.

Sent from my SAMSUNG-SGH-I317 using Tapatalk

 

[i8tokyo]

 

[i8tokyo]

 

[i8tokyo]

 

[Jacko]

I seriously tried to use the force for like 5 minutes to get the screw gun. Too lazy to climb down off the scaffolding

hahaha. I tried that once when 5m off the ground on scaffolding when I dropped a paint brush. Sadly, the force was not with me.

 

[Shoottx]

Great shop build.

Just read the whole post from the start, I guess I missed the earlier part prior to my joining GJ.

Yup been through the afib mess. After 5 years of messing with every drug therapy possible, finally did the ablation. Wish I had done it sooner, no problems for the last 3 years. (with the heart, won't go into others). Getting old isn't for sissies.

You mentioned you were in will county, where abouts? I know the ares pretty well, Grew up in Dwight. Glad to be out of the white stuff

 

[i8tokyo]

 

[i8tokyo]

 

[i8tokyo]

 

[i8tokyo]

 

[i8tokyo]

so I got my old box in the barn and cleaned up and in its spot. they sure changed the style in 3 or 4 yrs. whatever its going to be a mix and match room. had to throw down plywood to get the stuff in. well worth blowing 8 sheets of osb. moved a total of 8 of the tall cabinets. 4 red ones in and 4 ugly tan ones in. no room for the side box, probably going to rebuild the welding cart and use it.

 

[i8tokyo]

 

[i8tokyo]

 

[i8tokyo]

going slooow. got the counter top cut down and installed for the bench and I got the wireless extender installed so I can have internet. pandora!!!! shelves and stereo tomorrow. thought I was going to get it done today. going to be a short day tomorrow. going to see lindsey Stirling at the Riv

 

[Crown]

Those new cabinets and drawers are really clean. Nice looking workspace you've got yourself there.

 

[i8tokyo]

Sent from my SAMSUNG-SGH-I317 using Tapatalk

 

[i8tokyo]

 

[i8tokyo]

 

[i8tokyo]

So I have been working on finishing up my pool house and just got back to this. Ready to blow fiberglass in the walls then close up the soffit. Was going to do cellulose but we had an ugly storm and I got some water through a few seams. So I am more afraid of mold with paper then fiberglass I guess. I should have forced them to use the mastic tape one the seams. I m too damn nice. And cheap.

 

[thetastelingers]

Your tool room is great!

 

[jjohnson70]

Your tool room is awesome! Is that a laminate floor in there?

 

[i8tokyo]

Yeah but its waterproof one. Shaw I think is the brand. It dose scratch though. Daughter found out the day after it got put down by dragging my hooptyass stool. She felt so bad.

 

[i8tokyo]

tool rooms not so clean. Gotta get my wood shop done so I can make upper cabinets. Really need to hang the doors but I am not sure what cool to paint the trim. Might do red

 

[Jacko]

that is going to be an awesome shop when finished. It just keeps getting better and better!

 

[metalhead140]

Looking good!

 

[Wuaname]

so i added a 10inch bazooka tube yesterday. sounds a bit better

Ahh a real sound system vs just bluetooth speakers

Nice chests and black / red

 

[motofool33]

nice, are those file cabinets you putnear the tool boxes?