Above 1200 Sq/FT Plugger Workshop

[Prospecter]

More caning pictures. The redo will be the same process, but will work better with smaller can.
x
More pictures of sawdust bricks being delivered.

The porch (aka "Camp") is next to the attached garage, is handy for storage.

 

[drivesitfar]

You’ve certainly got many skills!!

Sawdust bricks similar to the old presto logs? A lot less labor intensive than cutting up firewood and guessing they are pretty efficient and not overly spendy?

Looks like the weather is perfect snd nothing better than watching nature and the critters out there in your view.

Have another grand weekend.

 

[Prospecter]

You’ve certainly got many skills!!

Sawdust bricks similar to the old presto logs? A lot less labor intensive than cutting up firewood and guessing they are pretty efficient and not overly spendy?

Looks like the weather is perfect snd nothing better than watching nature and the critters out there in your view.

Have another grand weekend.

Thanks.

Sawdust bricks are indeed similar to Presto Logs, though less expensive. We can burn them in our wood stoves. Very clean and efficient, although I probably would burn them anyway, because I've had wood fires most of my life and like them. They are compressed sawdust, like wood pellets, only bigger.

Price is about the same as if I bought my wood cut and split, and then stacked it myself. Both are competitive with oil and propane, although all the prices fluctuate. I don't focus on the prices much. I like the wood stoves, and cutting / splitting firewood is getting a bit much.

The weather is nice, but very hot. Seems like very hot weather goes with moving!

 

[Prospecter]

Used a biscuit joiner and Z clips to attach card table top to the legs. The top had previously split because it was attached with many screws so the table could not expand and contract with the seasons.

I cut off the damaged veneer on the desk, to see what there was to deal with. Eventually I cut back a little more to get a square edge to mate with the new veneer. Some of the underlying plywood layers also needed to be glued. I used Super Glue for that. Not shown, but both the left and right sides also have damaged veneer that I removed.
e

 

[Prospecter]

The groundhogs are messing with my garden. The wire hoops I made to protect the tastiest of my crops foil the deer and turkeys, but the groundhogs just walk under the hoops. They don't quite fit, so the hoops ride on their backs and are moved out of position.

 

[Jayman17]

Good idea using a biscuit joiner to cut slots for your Z clips. I'm going to make a mental note of that.

 

[drivesitfar]

Nice work on the table repair and dare I say genious fix. I know you like critters and birds and all that Mother Nature has to offer but like you there are the pesky ones that seem to take more than their share or do damage too.

You at least got him posing and can you send a sleeping dart his direction and have him wake up on another mountain?

Keep up the great stuff and hope your sale on the other property is a smooth transaction.

 

[Prospecter]

Measuring and cutting the veneer to fit. I lined up the left and top, and then overlayed the right hand side. I cut through both layers, and removed old bottom layer on the left, and new top layer on the right. Oddly, the veneer grain runs vertically instead of horizontally.

Removing excess veneer up to the cut line.

Cleaned up the hardware - Before and after. The knobs are mostly steel except for the button that shows.

 

[Prospecter]

Brushing on contact cement on both the desk and veneer. This is the highly flammable stuff, so all the windows were open.



Same procedure on the other side, except the left butts up against the rear leg, which is a little out of plumb. I fit the top and left side first, then cut through both layers on the right side as before.

Trimming the bottom edge flush. I left the edge slightly proud of the underlayment, then gently sanded the new edge to match the old.

 

[drivesitfar]

You’ve got skills!!!

 

[Prospecter]

I put the desktop piece of veneer on today, and got a coat of stain on. The stain turned out to be a good match, which is a relief. Likely the veneer mahogany is a different species from that used originally, so I am pleased to have the stain minimize the differences.

Tomorrow, I need to meet the ramp truck guy up north to move the 2038 to the Mid-coast.

 

[Jacko264]

Hi mate
mine your fingers with that knife

your doing a great job
Graham

 

[Prospecter]

Hi mate
mine your fingers with that knife

your doing a great job
Graham

It does look a little risky from that angle, but my left hand is well below the knife in my right hand.