Show your new tool arrivals
- Thread starter sarel.wagner
- Start date
at least 2 molds... one for the ones that actually say china on the side and another for those that say nothing
If those bolts are on a 94-01 Ram 1500, I think they are 14mm. Or at least mine are. I've done this a few times in 155k miles on mine, and in my experience, I'd say the chances of an axle shaft seal leak or wheel bearing making noise afterwards is about 50/50.
If it doesn't have the ir logo and says titanium on the hammer case then its a 2112 which is the same as a older 2115 except for the 7th slot on the cylinder
Attachments
Last edited:
Jarhead0408
Well-known member
WOW! This page is FULL of win today! Congrats fellas!
Got these for $40
Please share source where you got them for $40 if you don't mind.
If those bolts are on a 94-01 Ram 1500, I think they are 14mm. Or at least mine are. I've done this a few times in 155k miles on mine, and in my experience, I'd say the chances of an axle shaft seal leak or wheel bearing making noise afterwards is about 50/50.
97 Jeep ZJ
RXtacy
Well-known member
Adding to the green hammer trend.
I don't know where he got his from. But you might want to try Sears. They go on sales once in a while just need to keep your eye on when it's on sales. And depends on points, you could get them cheaper.
E46erak
Member
Finky198
Well-known member
I am pretty sure it 13mm and not 1/2"
I have to replace the hubs on my 98 ZJ
I would say buy 2 of those sockets as the bolts have a tendcy of not being easy. Wether it's a broken socket, breaker bar ... If you have a 3/8 impact and a 12pt chrome socket you might get lucky with access (about the only time I Condone using my chrome on an impact as nothing else seem to fit)
Last edited:
jinx
Well-known member
Stuff bought over the last 2 months.
Love the hammers just wish my driver could find the smaller one in orange.
The 1/4 snappy. sockets are replacing my Tektons that kept turning to ****.
Not a tool but thought I'd share it anyways. 2015 Focus ST [emoji48]
Sent from my XT1097 using Tapatalk
Love the hammers just wish my driver could find the smaller one in orange.
The 1/4 snappy. sockets are replacing my Tektons that kept turning to ****.
Not a tool but thought I'd share it anyways. 2015 Focus ST [emoji48]
Sent from my XT1097 using Tapatalk
thegroundpounder99
Well-known member
Stuff bought over the last 2 months.
Love the hammers just wish my driver could find the smaller one in orange.
The 1/4 snappy. sockets are replacing my Tektons that kept turning to ****.
Not a tool but thought I'd share it anyways. 2015 Focus ST [emoji48]
Sent from my XT1097 using Tapatalk
You will love the Focus, I got one on Labor Day lol. Congrats!
Sent from my iPhone using Tapatalk
jinx
Well-known member
Thanks. It's a very nice upgrade from my 2010 mustang I had. Hopefully I can buy a tuner for it.
Sent from my XT1097 using Tapatalk
JonDick13926
Well-known member
Dennis Leigh Henry
Well-known member
skulldrinker
Well-known member
When i saw this on my local for sale site i almost had a heart attack. Before my brain could figure out if the price was a mistake or not i noticed it was sold already. Maybe the person who bought it will post it here. Oh and tools included .
Sent from my LG-H811 using Tapatalk
Sent from my LG-H811 using Tapatalk
turns out they are 13mm.. someone lied and told me 1/2"... well it is convincing given the strange mix of SAE and metric throughout
managed to get them with a 1/2" drive socket and my 24" matco ratchet... then couldn't get the hub to come loose... yay 19 years of rust... i guess on the bright side when i give it another try the bolts should be easier to take off
anyway... i got this tday
Thanks heading to the mall tomorrow so will surly check them out
I have the 1/4 and 1/2 drive versions. The 1/4 is my favorite small ratchet, the 1/2 is good, but for some reason I go back to the Williams. I think it is the bulky head and short handle.
I use the 1/4 in "spinner" mode a lot. The 1/2 is my only flex so it does get lots of use, but for some reason it's not the one I pick up when I just need a ratchet.
I would buy them both again however.
dutchgray
Well-known member
View media item 54533Got a used (barely) SK thumb wheel off eBay for a lot less than a new one, not much SK about here, so this is a rare find here.
Askme42
Well-known member
rodsnratfinks
Well-known member
What did those set you back?
Askme42
Well-known member
On sale at Amazon for like $35 right now.
Askme42
Well-known member
Sorry $40
rodsnratfinks
Well-known member
Nice. I shouldn't have asked. Trying not to make any purchases for a while.
Sent from my SM-G920V using Tapatalk
Sent from my SM-G920V using Tapatalk
ihateminimumwage
Well-known member
- Joined
- Jan 26, 2012
- Messages
- 3,960
I absolutely agree. Have them in SAE (and a single 10mm).
Askme42
Well-known member
I usually tell the wife what to get me for gift giving holidays. Then she surprises me with something else from my Amazon wish list. Last year she got me the SAE set but I use metric way more.
My brother got me an Amazon gift card recently and thought bam know exactly what I'm getting.
Now to find a project. Lol
Askme42
Well-known member
I can understand that, I am trying to hold off until after the holidays, I have a feeling I am going to be getting sioome decent quality tools. But I always see something on here I want.
66HertzClone
ALLIANCE MEMBER
I can't read the manufacturer on the handle, have a link to them on Amazon please?
Askme42
Well-known member
Yep. That's them.
66HertzClone
ALLIANCE MEMBER
Thanks
Love my wiha screwdriver set. When my craftsman nut drivers start going south, I will pick up a set of those. Nut drivers are so handy.Do you have a link? Can't read the writing from the picture. My wallet will probably regret asking for this...