Show your new tool arrivals

[KMdef9]

Went to HF to use the 25% on a toy for me:



Of course had to upgrade the 1/4 fitting:



Opted for the warranty, 2 years for $35. So $110 +tax.

Of course got a free item, didn't have the 36" grab tool.

 

[Finky198]

Is that for the shop press mod?

 

[dodge610]

What's the COO of origin? I'm thinking those are made by Vessel.

Dont know will look on back of packaging tomorrow.

 

[KMdef9]

Is that for the shop press mod?

No, fits under all 3 of my vehicles. Allows me to jack the car up with both in garage. Luxury tool ATM.

But am curious now, PM info on that.

 

[Finky198]

It just replaces the stock one from HF 20 ton press to add the air operarate function. That's all

 

[Moparman390]

It's Japan on the impact screwdrivers, saw them in store already.

 

[oxycodone]

Sk 1/4" drive flex ratchet.

 

[bert1913]

https://www.amazon.com/gp/product/B00OKGAERO/?tag=atomicindus08-20

 

[Bobcat753]

I needed to offset all the big tools I have been buying

 

[PelicanPines]

I needed to offset all the big tools I have been buying

I have that gearwrench ratchet... it has so much back drag I never use it... will take it apart to figure out if I could make it a LOT MORE smooth.

It's basically a breaker bar it's so stiff.

 

[Bobcat753]

I have that gearwrench ratchet... it has so much back drag I never use it... will take it apart to figure out if I could make it a LOT MORE smooth.

It's basically a breaker bar it's so stiff.

Try this stuff, Prather Cable Grease, I put it in 2 coarse tooth ratchets and it made them smoother than butter. I now use it on EVERYTHING and it works awesome.
https://www.offshoreelectrics.com/proddetail.php?prod=hpi-pra7145

 

[PelicanPines]

Try this stuff, Prather Cable Grease, I put it in 2 coarse tooth ratchets and it made them smoother than butter. I now use it on EVERYTHING and it works awesome.
https://www.offshoreelectrics.com/proddetail.php?prod=hpi-pra7145

Thanks... the trick is opening this ratchet...

 

[Bobcat753]

Thanks... the trick is opening this ratchet...

There should be a small C clip on the drive side. Take a 90 degree mini pick and get underneath and slide the pick around until it pops out. You might need to take a thin feeler gauge to first get underneath the C clip.

 

[PelicanPines]

There should be a small C clip on the drive side. Take a 90 degree mini pick and get underneath and slide the pick around until it pops out. You might need to take a thin feeler gauge to first get underneath the C clip.

Thanks... also need to do it after the first cup of coffee... not the ninth.

 

[Ruger_556]

 

[chrisnazzy]

1. Caved on the 1/4" Wobble Plus set for $100 plus freebie bottle opener

2. Finally remembered to order a Snapon YA905 boot for my Milwaukee ratchet for $5.20.

3. My Mac guy got me this Streamlight HL in orange and traded me for the standard blue one I had received. Gave him $20 for taking the blue one off my hands and the upgrade to the HL.

4. Picked up one of these Makita wobble 3/8" adapters after seeing one another member posted.

5. Not really a tool but I added a gloss black magnetic "S" to my bottom drawer for a little spiff up of my box I've had for 9 years.

Sent from my SM-G930P using Tapatalk

 

[ADSR]

1. Caved on the 1/4" Wobble Plus set for $100 plus freebie bottle opener

2. Finally remembered to order a Snapon YA905 boot for my Milwaukee ratchet for $5.20.

3. My Mac guy got me this Streamlight HL in orange and traded me for the standard blue one I had received. Gave him $20 for taking the blue one off my hands and the upgrade to the HL.

4. Picked up one of these Makita wobble 3/8" adapters after seeing one another member posted.

5. Not really a tool but I added a gloss black magnetic "S" to my bottom drawer for a little spiff up of my box I've had for 9 years.

Sent from my SM-G930P using Tapatalk

wow! That's going to be a sore wallet.

 

[stonesfan68]

I have that gearwrench ratchet... it has so much back drag I never use it... will take it apart to figure out if I could make it a LOT MORE smooth.

It's basically a breaker bar it's so stiff.

Thanks... the trick is opening this ratchet...

There should be a small C clip on the drive side. Take a 90 degree mini pick and get underneath and slide the pick around until it pops out. You might need to take a thin feeler gauge to first get underneath the C clip.

This post may help you get the ratchet apart. I put Permatex 81950 (engine assembly lube) inside of the ratchet and it worked like a charm.

http://www.garagejournal.com/forum/showthread.php?t=78652

 

[chrisnazzy]

wow! That's going to be a sore wallet. [emoji38]

Less than $150 for all that isn't too bad.....

Sent from my SM-G930P using Tapatalk

 

[Redemption]

 

[redvalkyrie]

It's Japan on the impact screwdrivers, saw them in store already.

Okay, then those have to be made by Vessel. I love my Vessel tools. Their screwdrivers are among the best around.

 

[rshadd]

Park Tool GG-1 Grease Gun

 

[fdc319]

Upgraded my 1/2" drive game with a set of SK deep sockets. 10-24mm delivered today.

Conveniently also waiting on my front step was my warranty replacement 45183 SK flex head 3/8" drive. Chrome pealed off the head, so they replaced it no questions asked. Love this ratchet.

 

[willjogervais]

SK x frames are here!

 

[02Xterra]

Bought the impact from ToolUp on ebay, got it down to $129 after a $50 gift card



Sent from my VS986 using Tapatalk

 

[bert1913]

#1 https://www.amazon.com/dp/B0015BEHYS/?tag=atomicindus08-20

#2 https://www.amazon.com/dp/B0038G3RCQ/?tag=atomicindus08-20

#3 https://www.amazon.com/gp/product/B007BI7IJA/?tag=atomicindus08-20

since i already own plumbers ****, i might as well own some plumber tools

 

[M_George]

Let me know how you like No 1, the Ridgid sink installer. I've had one on my get list.

 

[Finky198]

I had to a 35max it was new on eBay for $100 got the boot for $22 on tooltopia...

 

[Tenex]

I grabbed the 2704 hammer-drill off of let-go for $80 and he gave me the case too. It's dated November 2016 so I've still got plenty of time before the warranty expires.

 

[NoahG]

Finally got myself a JIS #2.

Also a 1/8" Xcelite.


Sent from my iPhone using Tapatalk

 

[Finky198]

$24 opening bid used snap on 206AFSA 3/8"'6pt universals 7/16"-3/4"

 

[L.Cheapo]

$24 opening bid used snap on 206AFSA 3/8"'6pt universals 7/16"-3/4"

Congratulations, sir. You ****!

 

[Finky198]

Thank you

 

[HanShotFirst]

$24 opening bid used snap on 206AFSA 3/8"'6pt universals 7/16"-3/4"

Okay that gets you a "You ****"!! Well done sir.

 

[driftpin]

I sold an elderly Craftsman 5 drawer toolbox I got at a yard sale for $10, used some leftover Rustoleum paint on it, sold it on Craigslist in a couple of weeks, and promptly bought these tools off Craigslist, a 2 ton engine lift, and a engine stand, from a FL transplant from IN who sold his '66 Chevelle 402 cu.inch playtoy and didn't need 'em anymore. $80 for both, and the toolbox sold for half that, so the end cost was $50 for the two (including the original toolbox cost), a hydraulic hoist and engine stand.

I'm selling two Pontiac 389, 1966 engine/transmissions and a complete 400 1973 Pontiac Formula 400 engine, auto ******, driveshaft, and rear end drivetrain for a friend. The engine hoist will help me to move them. The engines are complete w/all accessories, they came out of a couple of Star Chiefs, and he has SS trim for the Star Chief body too, a hood and 3 doors (4 dr style body. Cheap prices, stored inside, 1 is a 4 bbl, 1 is a 2 bbl, and the 400 is a 4 bbl. I have pics for ID'ing the engines. PM me if interested.

 

[bubinga]

$24 opening bid used snap on 206AFSA 3/8"'6pt universals 7/16"-3/4"

Congratulations, sir. You ****!

Thank you

Okay that gets you a "You ****"!! Well done sir.

ME Three,, or is it 4?
MY OH MY, how did that slip through.
Awesome.

 

[TorKe]

I grabbed the 2704 hammer-drill off of let-go for $80 and he gave me the case too. It's dated November 2016 so I've still got plenty of time before the warranty expires.

I don't like you. Right now.

 

[PureLeaf]

#1 https://www.amazon.com/dp/B0015BEHYS/?tag=atomicindus08-20

#2 https://www.amazon.com/dp/B0038G3RCQ/?tag=atomicindus08-20

#3 https://www.amazon.com/gp/product/B007BI7IJA/?tag=atomicindus08-20

since i already own plumbers ****, i might as well own some plumber tools

Whats the country of origin on the RIDGID 27023 Model 2002 One Stop Wrench ?

I know it used to be Germany, but heard they'd switched it to China. The german ones had "made in germany" on them.

 

[Wamsutta]

Finally got myself a JIS #2.

Also a 1/8" Xcelite.


Sent from my iPhone using Tapatalk

Is that handle as comfortable as it looks? It looks real comfortable.

 

[Bobcat753]

After 5 years of not owning a decent jack besides various bottle jacks I picked up this today. Super happy and this should last for a LONG time for my needs.