To avoid these ads, REGISTER NOW!

Snap-On, Mac, Miscellaneous

Schurkey

Well-known member
Joined
Oct 27, 2011
Messages
2,378
Location
The Seasonally Frozen Wastelands
Looking to sell a few items:

Blue Point Tube Bender $15
TubeBender_01.jpg


TubeBender_03.jpg


Snap-On speed handle $30 SHIPPED in the USA
Snap-On_38_Speed_Handle_01.jpg


Snap-On_38_Speed_Handle_02.jpg


Snap-On pry-bar set. Almost perfect. $110
Snap-On_4Prybars_05.jpg


Adding more items later as I get photos processed and uploaded...
 
Last edited:
To avoid these ads, REGISTER NOW!
OP
S

Schurkey

Well-known member
Joined
Oct 27, 2011
Messages
2,378
Location
The Seasonally Frozen Wastelands
Are prices including shipping?
No, but I'll ship at cost within the USA. I like Priority Mail, but I can make other arrangements if buyer wishes.

I'll take personal checks (will wait to clear) US Postal Service money orders (ships immediately) or PayPal (+3%)

Outlander800--PM with your preferred shipping method and choice of payment. Thank You!
 
Last edited:
OP
S

Schurkey

Well-known member
Joined
Oct 27, 2011
Messages
2,378
Location
The Seasonally Frozen Wastelands
Metric Flare Nut Wrenches One MAC (Rare! "ratcheting" open-end) One Snap-On. The photos look dark, these wrenches are ordinary chrome with some scuffs; but not "black chrome" or anything unusual. $35/pair SHIPPED in the USA.
Flare_Nut_Metric_forsale_04.jpg


Flare_Nut_Metric_forsale_03.jpg


SAE Flare Nut wrenches Snap-On $40/Pair SHIPPED in the USA.
Flarre_Nut_SAE_RKH_02.jpg


Flare_Nut_SAE_38_916.jpg


I'll have a 5/8--11/16 flare nut wrench for sale if I can buy a Snap-On RSXS22 11/16 flare nut/ratcheting open end wrench (haven't found one yet...)

Snap-On air impact wrench IM510B 1/2 drive $110 SHIPPED in the USA

Waiting on photos
Snap-On cylinder-shorting tach dwell


There's more; I need time to sort through stuff, make some decisions, and take/process photos.

Snap-On LOW TORQUE air ratchet 3/8 drive FAR70B $60 SHIPPED in the USA
I have owned it since about '86. It has not been used much since about '90 when I quit auto repair as a profession. Hobby use only since then. I oiled it and connected to air two days ago--works fine.

I used it primarily to remove and install spark plugs. This is a LOW TORQUE air ratchet, (note the size of the air motor!) so there was no danger of over-torquing the plugs. Start the plug threads by hand to prevent cross-threading, hit the trigger, wait for the ratchet to stall--move to the next plug. The long handle allowed me to break-free tight plugs, and then use the air to remove them. It worked better than the 1/4" drive "mini" air ratchets for breaking tight spark plugs free because of the longer handle.

Has a two-speed trigger, and with the trigger fully depressed, is a bit "faster" than a typical air ratchet. Air exhaust is rotatable 360 degrees. Ratchet makes a distinct sound; lower-pitched and fairly quiet compared to the typical air ratchet. Easier on the ears. Is excellent for any "delicate" work--small-to-medium stuff that has clean threads; or will be torque-wrenched to final tightness. Would be good for installing/removing transmission valve bodies; or perhaps engine assembly--speedy for running down nuts 'n' bolts, but not so powerful that it'd get you into trouble.
Snap-On_FAR70B_01.jpg


Snap-On_FAR70B_02.jpg


Snap-On_FAR70B_03.jpg


Snap-On MT2500 v.2.2 scan tool $310 SHIPPED in USA

Snap_On_MT2500_01.jpg


Snap_On_MT2500_02.jpg


GM1, GM2, Ford1A, Ford4, Chrysler1, Chrysler2, Jeep1, Multi1, OBDII, 12V power cord, Personality Keys K1, K3, K8, K9, K13.
Snap_On_MT2500_03.jpg


Snap_On_MT2500_06.jpg


Snap_On_MT2500_07.jpg


Mac stubby 3/8 ratchet XR1 $35 SHIPPED in USA
Chrome worn a little. Doesn't show up well in photos, and isn't that noticeable in person--mostly on upper part of first photo.
Mac_XR1_01.jpg


Mac_XR1_02.jpg


Craftsman 4-wrench set in plastic pouch. TINY wrenches. $12 SHIPPED in the USA
Craftsman_Ignition_01.jpg


Craftsman_Ignition_02.jpg


I'll combine shipping where possible.
 
Last edited:
OP
S

Schurkey

Well-known member
Joined
Oct 27, 2011
Messages
2,378
Location
The Seasonally Frozen Wastelands
Ooops. Forgot this one. Imperial Eastman tubing bender. 364 FHA 12 (3/4 tube) $70 SHIPPED in the USA

Eastman_Bender01.JPG


Eastman_Bender02.JPG






Also: TWO Starrett dial bore gauges. BOTH are damaged and need repair. ONE set of "rods" to adjust for different bore sizes. $40 for both, SHIPPED in the USA.
Starrett_Bore_Mic_005.jpg


Starrett_Bore_Mic_007.jpg
 
Last edited:
To avoid these ads, REGISTER NOW!

fordbroncodave

Well-known member
Joined
Sep 15, 2009
Messages
4,555
would you sell the 3/8" X 7/16" flare and the 10 X12 flare wrenches together to me? PM me a price
 
OP
S

Schurkey

Well-known member
Joined
Oct 27, 2011
Messages
2,378
Location
The Seasonally Frozen Wastelands
Added a bunch of photos of additional tools into earlier posts. All the newly-added tools show a price including shipping. I think that I made a mistake in not doing that to begin with--I was trying to leave shipping costs open in case someone bought multiple items; and then I'd combine shipping. I'll revise those prices to reflect shipping included when I get time.

Have contacted all the "first in line" folks regarding shipping costs. (If you didn't receive the PM, POST HERE.) Another day or so, and I'll let the "second in line" have a shot at them.
 
Last edited:

mooman

Well-known member
Joined
Jun 9, 2005
Messages
2,791
Location
CHICAGO, IL
Normal scuffs to chrome. Drive end still tight. Marks on "fork" from drive end as shown in these photos:
Snap-On_Breaker_03.jpg


Snap-On_Breaker_04.jpg


Again, normal chrome, photo is dark--bad lighting, I guess.





Done.

No mention of engraving in the listing. How bad/deep is the engraving?
 
To avoid these ads, REGISTER NOW!
Top Bottom