Installing a TMG tpl45 10k symmetrical 2 post lift in my garage. Unfortunately the bay is only 23' deep. I will be lifting mostly cars and full size suv's occasionally.
In my last garage at my old house I installed a asymmetrical lift in a 19' deep bay positioned 10.5' off the shop door with a lot of planning and it worked out great for my old cars, since I had room in the front for engine work and very little at the rear.
I'm hoping somebody with a symmetrical lift and a full aize suv such as a yukon xl, suburban, expedition or excursion can throw it on their lift and do some measurements for me.. barely a 1 beer job! I'd love to know the measurement from the centre of post to front of vehicle and centre of post to rear of vehicle. A full size crew cab pickup would work asell.
My rough thought is to mount it approximately 10' from the door but I haven't actually had time to move the vehicles around and take measurements.
Any input? Bolting this thing down tomorrow! Thanks
Quote Reply
Report •••
BoldItalicMore options…
Insert linkInsert imageMore options…
UndoMore options…
Preview
Font sizeText colorFont familyListAlignment
SmiliesQuoteMediaInsert tableInsert horizontal lineSpoilerCode
RedoToggle BB codeRemove formattingDrafts
Write your reply...
Post reply
Attach files
In my last garage at my old house I installed a asymmetrical lift in a 19' deep bay positioned 10.5' off the shop door with a lot of planning and it worked out great for my old cars, since I had room in the front for engine work and very little at the rear.
I'm hoping somebody with a symmetrical lift and a full aize suv such as a yukon xl, suburban, expedition or excursion can throw it on their lift and do some measurements for me.. barely a 1 beer job! I'd love to know the measurement from the centre of post to front of vehicle and centre of post to rear of vehicle. A full size crew cab pickup would work asell.
My rough thought is to mount it approximately 10' from the door but I haven't actually had time to move the vehicles around and take measurements.
Any input? Bolting this thing down tomorrow! Thanks
Quote Reply
Report •••
BoldItalicMore options…
Insert linkInsert imageMore options…
UndoMore options…
Preview
Font sizeText colorFont familyListAlignment
- Align left
- Align center
- Align right
- Justify text
SmiliesQuoteMediaInsert tableInsert horizontal lineSpoilerCode
RedoToggle BB codeRemove formattingDrafts
Write your reply...
Post reply
Attach files
Similar threads
- W
2008 my Genie tz50 towable lift beepeing.- Started by whosurpopi
- Yesterday at 12:00 PM
- Replies: 2
- L
Scissor lift batteries- Started by lynnbilodeau
- Nov 11, 2024
- Replies: 7
- E
4 Post Lift Recommendations- Started by EDS01SS
- Nov 2, 2024
- Replies: 17
- B
Looking to buy a Lift- Started by bad_idea
- Oct 27, 2024
- Replies: 3
- W
How to find a replacement sheave shaft for an unknown brand 4 post lift?- Started by waygeekierthanu
- Oct 24, 2024
- Replies: 6
- C
Help with my American Unic CM-3BD 240V car lift- Started by centipede
- Sep 29, 2024
- Replies: 12
- S
Thinking About Buying a Used Car Lift from Boom & Bucket – Any Experiences?- Started by scfoxman
- Sep 18, 2024
- Replies: 2
- N
I have an Atlas lift. I have burned one motor and a second worked for a bit. I am on my third pump. The motor spins but th elift will not go up.- Started by ng8264723
- Sep 8, 2024
- Replies: 3
- M
A little update on my Chinese lift I installed in 2015- Started by mike1956
- Sep 8, 2024
- Replies: 6
- M
Lifting large tool with 2-post lift. Am I going to to regret this?- Started by mears
- Sep 1, 2024
- Replies: 17
- Brought to you by:Atomic Industry
- Contact us
- Terms and rules
- Privacy policy
- Help
- RSS
- Links on The Garage Journal are affiliated by SOVRN.
- The Garage Journal would like your permission to enable push
