Welding table build

[Bears Fan]

Just awesome!

 

[Mike.ASC]

High quality work and well designed.

 

[zmotorsports]

Beautiful workmanship, design and execution.

 

[z-edition 006]

z-edition 006 that is a piece of art work, well done.

Just awesome!

High quality work and well designed.

Beautiful workmanship, design and execution.

Thanks for the great feedback guys.

 

[z-edition 006]

I use a mag drill to drill holes for screwing the table top to the frame. The screws are M10 X 25mm. I had to shorten the four 36mm sockets, and weld them back together again. These will be there permanent, so i can adjust the table legs as i want.

 

[z-edition 006]

A few more pictures:

 

[Boosted1]

Very nice.
Excellent work.

 

[N2 Many Projects]

This table is coming along very nice.

 

[Jawfish]

Very Nice, I really like the side table for the cut off saw and the side extension. Beats cutting steel on your knees...

Hope you don't mind if I steal some of your design ideas.

Cheers,

Fred

 

[z-edition 006]

Very nice.
Excellent work.

This table is coming along very nice.

Very Nice, I really like the side table for the cut off saw and the side extension. Beats cutting steel on your knees...

Hope you don't mind if I steal some of your design ideas.

Cheers,

Fred

Thanks. I don't mind. I found many of the ideas on this forum and other ones.

Here is the progress for today. A brand new vice for the welding table:

 

[1/2 Cup]

z-edition 006 sweet

 

[yaidunno]

Glad to see that top being bolted on vs. welded! Those Ridgid vises are very nice, I think you will enjoy using it a lot.

 

[RedTailHawk]

Re: Diy welding/fabrication table

This might be one of my favorite designs for my situation. Will you post final design and parts list?


Sent from my iPhone using Tapatalk

 

[Keyblazer]

Really nice!

Wish I could weld like that!

The receiver hitch dealio is great... I've already got that going on in my little shop, so no reason not to, as It will just make my future fab table flexible!

I gotta ask... where do you guys get your table tops?
I simple cant afford to buy a 1/2 plate around here... Im probably going slatted because of that!

 

[z-edition 006]

z-edition 006 sweet

Thanks.

Glad to see that top being bolted on vs. welded! Those Ridgid vises are very nice, I think you will enjoy using it a lot.

They have a good reputation over here.

This might be one of my favorite designs for my situation. Will you post final design and parts list?

I can look into that later, when the table is done.

Sent from my iPhone using Tapatalk

Really nice!

Wish I could weld like that!

The receiver hitch dealio is great... I've already got that going on in my little shop, so no reason not to, as It will just make my future fab table flexible!

I gotta ask... where do you guys get your table tops?
I simple cant afford to buy a 1/2 plate around here... Im probably going slatted because of that!

A company in Norway cut the plate for me. I payd for the labour and the weight for the steel plate. Not cheep but ok.

Just started to make a manual turn table for my welding table. Here are some picture of that. I got this idea from a great welder. He calls him self txsviking on youtube.

Here is the link:

 

[z-edition 006]

The welding table is now sandblasted, and ready for paint. I use muriatic acid to get rid of the mill scale on the table top.

 

[N2 Many Projects]

What will you treat the tabletop with to stave off rust on the surface?

 

[sweet victory]

Beautiful build! As someone still in the "sketching on napkins" phase of my fab table, this was some terrific inspiration.

 

[z-edition 006]

What will you treat the tabletop with to stave off rust on the surface?

I will just use WD-40.

Beautiful build! As someone still in the "sketching on napkins" phase of my fab table, this was some terrific inspiration.

Thanks.

 

[z-edition 006]

Anyone like my diy paint booth? Two coats of primer done.

 

[Dragoonmc]

Re: Diy welding/fabrication table

That paint booth is a darn good idea


Sent from my iPhone using Tapatalk

 

[z-edition 006]

Re: Diy welding/fabrication table

That paint booth is a darn good idea


Sent from my iPhone using Tapatalk

Yes i think so. I can re use it on another project later.

 

[N2 Many Projects]

Pretty fancy booth.

 

[svrider]

What's your ventilation setup in the spray booth?

 

[z-edition 006]

Pretty fancy booth.

Thanks.

What's your ventilation setup in the spray booth?

I don’t have any ventilation at this point. I use a Sundstrøm SR100 as a mask, and a dehumidifier with heat. Then i can keep the moisture level low and perfect temperature for painting. I don’t use spray paint, but i use a paint brush for very fine finishes.

First layer of red paint:

 

[1/2 Cup]

z-edition 006 now that is thinking out of the square with the spray booth.

 

[z-edition 006]

Totally four layers of red paint later, it looks like this:

 

[z-edition 006]

Some more progress:

 

[Bears Fan]

Oh that may be a little too prurdy to use now

 

[Duker]

Ok, this is bittersweet for me.... you took my concept and raised the bar at least 3 notches with the adjustable legs, manual turn table and better execution...all of which is awesome... and the best compliment I can give is that you have made me a little jealous of my own table...lol. However, the bad news is that now you have kicked in my ocd and have made me add to my already long to-do list to repaint my table!

Seriously, the table has turned out great and I am going to have to add that turn table to mine as that was a great idea and well executed.

 

[z-edition 006]

Oh that may be a little too prurdy to use now

Yes i know.

Ok, this is bittersweet for me.... you took my concept and raised the bar at least 3 notches with the adjustable legs, manual turn table and better execution...all of which is awesome... and the best compliment I can give is that you have made me a little jealous of my own table...lol. However, the bad news is that now you have kicked in my ocd and have made me add to my already long to-do list to repaint my table!

Seriously, the table has turned out great and I am going to have to add that turn table to mine as that was a great idea and well executed.

Thanks for the positive feedback. You where on of those personns who gave me inspiration to start my own build, thanks again.

Just mounted the table top today.

 

[larry4406]

Truly an awesome build!

 

[z-edition 006]

Truly an awesome build!

Thanks.

A few more hours in the garage result in this.

 

[LXCam]

Beautiful workmanship, design and execution.

I'll double down on Mikes comments. Absolutely gorgeous work.

I gotta ask... where do you guys get your table tops?
I simple cant afford to buy a 1/2 plate around here... Im probably going slatted because of that!

Industrial metal supply brother. But right now isn't the time to buy a chunk.

Ok, this is bittersweet for me.... you took my concept and raised the bar at least 3 notches with the adjustable legs, manual turn table and better execution...all of which is awesome... and the best compliment I can give is that you have made me a little jealous of my own table...lol. However, the bad news is that now you have kicked in my ocd and have made me add to my already long to-do list to repaint my table!

Seriously, the table has turned out great and I am going to have to add that turn table to mine as that was a great idea and well executed.

I think I just witnessed the passing of the crown.

 

[z-edition 006]

I'll double down on Mikes comments. Absolutely gorgeous work.




Industrial metal supply brother. But right now isn't the time to buy a chunk.



I think I just witnessed the passing of the crown.

Thanks. I love your skills in Excel and fabrication on your Lista build.

 

[Boosted1]

Wow! That turned out awesome. Nice work.

 

[LXCam]

Thanks. I love your skills in Excel and fabrication on your Lista build.

Thanks Z, much appreciated.

 

[z-edition 006]

The table have now 240V power. Two double power outlets in the front and one double in the back. Totally 6 outlets.

 

[1/2 Cup]

z-edition 006 that is simply stunning

 

[z-edition 006]

z-edition 006 that is simply stunning

Thanks. I really love to work on this build. Now i have a good work surface for projects in the future.