Recent content by dthor68

  1. D

    I need a tool to remove pulley from PS Pump?

    Yeah, I heard that too. Could you use compressed air to clean it?
  2. D

    I need a tool to remove pulley from PS Pump?

    Are you saying that you removed the pully first while pump was still installed using 3/8 ext. to hold in place, then remove old pump, then install new pump, then install pully?
  3. D

    I need a tool to remove pulley from PS Pump?

    My Honda CRV's PS pump needs replacing and my new part does not come with a pulley. I do not own a impact drill so I will need a tool to help in removing pulley. I was looking at the Gearwrench 3900 pulley holder but it looks like it is more for removing fan clutch's, not sure if it will work...
  4. D

    Cutting plywood on a tablesaw?

    It looks like my square is 89.7. It is an Empire square. Can anyone here reccomend a good square for cabinet making? Thanks for all the help.
  5. D

    Cutting plywood on a tablesaw?

    Hopefully I can explain this correctly. Ok, so I am cutting some wood on a tablesaw. The piece of wood is 15" x 21" x 1/2" plywood. I make my 15" cut first, up against the fence rip. When I am done I measure top, bottom and center and it is perfect 15" wide throughout length. Now it is time for...
  6. D

    Champion Generator Maintenance?

    I never turned the shut off valve on. Fuel has not hit carb yet.
  7. D

    Champion Generator Maintenance?

    I bought a generator over the winter in case I lost power during a snowstorm. Never lost power. What should I do? Should I run it or drain fuel from tank and just store it until I need it. It is basically brand new. Even though there is fuel in it the tank it has never been opened. Other...
  8. D

    T-Track issues? (Router Table)

    I made myself a router table. In the top I have a T-track on both sides that allow me to move my fence back and forth and tighten it down where needed. It is the 3/4" wide by 3/8" deep T-Track with 5/16 T-bolts. All is made by Powertec. However, it does not move well. It gets hung up all the...
  9. D

    Painting Cabinets, Need Help.

    I have some oak cabinets that I want to paint white. I cleaned everything well with crud cutter, then sanded well with 220. I primed with Insl-x Stix, 2 to 3 coats. Top 2 coats is Benjamin Moore Advance. This all went fine and dandy with the cabinets. The doors did not do so well. Primer...
  10. D

    Vinyl Plank Flooring, Need Some Help!

    Can you control the depth of the toe kick saw?
  11. D

    Vinyl Plank Flooring, Need Some Help!

    My wife and I ordered enough vinyl plank flooring to do the entire house. Today I was getting ready by removing baseboards. While in the area of the kitchen/family room. where carpet transitions to linoleum, I ran across a problem. A big problem! At that transition, under the linoleum there...
  12. D

    Graco Magnum X-5 ?

    I am going to be painting my kitchen cabinets so I bought this unit to help get a smoother finish. Despite watching several youtube videos some questions I had were not answered. So, I have a few questions. 1) I will be giving the cabinets 2 coats of primer (Insl-X Stix) and 2 coats of paint...
  13. D

    Gearwrench tool reviews

    Gearwrench is a bit over-rated. But they are MUCH better than Craftsman, including US Craftsman.
  14. D

    Hobbies

    RATTLESNAKES! I love finding, observing and photographing Rattlesnakes. They are amazing creatures. Love all animals, Reptiles, amphibians, insects, spiders, birds, mammals and love photographing all of these animals. Love hiking and camping so I can find all of those animals to photograph...
Top Bottom