Recent content by fastrucken1

Ok guys I want to thank everyone for posting, I think we got little bit off topic (and that is mostly my fault) but I think some good info has come out of it that I really haven't seen before. I have been reading and researching on and off for the last 3yrs. I went back and forth on whether to...

So thanks for everyone's reply I was really looking for settings people were using for the takagi setup... OK now I'm going to throw a new rinkle has anyone looked at the rinnai m060sn. I can't believe nobody has mentioned this one (or a least that turned up in search) Its street price is...

The shop is 30x48x12 pole barn with scissor trusses fully insulated with 2" foam underneath and around of the edges of the 4" slab. R-19 in the walls and r38 in the ceiling and the garage doors are insulated. I have 5- 1/2 loops in the slab spaced at 12" and each loop is 287' long.

1. What circulator pumps are you using? 2. What kind of flow rate are you getting through your tankless (maybe include your model)? 3. What are your in and out temps in the primary and secondary loops that you shoot for? I really can't find any info on how to adjust the primary side. 4. Is...

cybrdyke... Thanks for the heads up.. . I ended up buying same bulbs from another wholesaler @ 6.50 a tube. I read most of the Best light fixture ever thread and honestly got lost with some of the updates. I think the 2 bulbs that Platonic Solid had pinned at the beginning of the thread were...

https://www.nugenled.com/collections/led-tubes-4-foot/products/12-watt-premium-dlc-t8-led-4-foot-tube-5000k-1-860-lumens-dual-end-bypass-case-qty-25-pieces-dual-end-direct-wire-or-plug-play They seem to be pretty efficient @ 155 lm/w 5yr warranty and DLC listed. Here is the spec sheet too...

Sorry I posted that from my phone.. If I run the metal perpendicular to the trusses I'am not sure that metal will lay out correctly. Each bottom chord of the trusses measure 15'1". So that means it will be 5 sheets per side (5 x 36"=15') and wont leave enough to overlap the peak. I think the...

Thanks for the replies... I'm still thinking about running the metal perpendicular to the trusses and know that will have to use firing strips... my trusses measure 15'1 inch from wall to peak... im little worried that if I run the metal front to back like you guys.. the spacing won't turn out...

Andy- I used a fellow garage journaler lead and used the same color scheme from here... Clicky I used the vinyl stripe method. I couldn't even imagine painting it. I was done with the stripe in less than 45 min, not bad for almost 140 ft..

Grump... Have any pictures by chance? I was actually planing on running the sheets the other way though....

So quick question... I'm going to put up a metal ceiling (still deciding between dura-panel and pro-rib from menards) in my shop but looking for ideas on how to finish the inside ridge or peak of the room, where the 2 sides meet in the middle (not sure of the proper name). Its a 30'w x48'L with...

So I've tried the lighting programs and couldn't make it work with a pitched ceiling and didn't see any layouts close to mind in that thread. The inside dimensions are 29'x47', 12 foot walls with a 4/12 pitched ceiling with the peak at 16'9" from the floor. My use for the building is just...

It is highly recommended to use one that can be used with solvents, it will usually say vition seals like this https://www.homedepot.com/p/ECHO-3-Gal-Sprayer-MS-300/204631876 However I already had the cheap backpack sprayer from harbor freight that i wasnt planning on using after this use...

So the cheapest fixture I found is from bees and they are the diva 4' @ 13.99. Now I havent called anybody to see if I could get much of a volume discount thou 40 pieces isnt a real high volume. The reasons you gave about being careful putting them up and may not ever have to touch them again...

So I tried to use the visual-3d tool but I cant figure out how to use it with scissor trusses and didn't see any other layouts with a vaulted ceiling. My shop is 30'w by 48'l with 2 garage doors at the gable end (the 30' side) with a white ceiling and white walls. The walls are 12ft and the...