Recent content by ford88

  1. F

    Lights by lift and under it

    Any ideas or pics of lighting for under 4-post lift its a little dark under it...ED
  2. F

    New, need advice on drawer liners.

    Re: New, need advices on drawer liners. I work for cintas the uniform people,they throw away mats that are stained or torn.Cut them up to size the best thing I have found for liners,These are rubber on back and carpet on top stays put and tools dont slide.
  3. F

    Restong a 73 Mach 1 need some advise

    Clean it up real good prime and use bed-liner you will never have to worry about it again.On my 66 fairlane I sandblasted it primed with epoxy and painted with eastwood chassis black.
  4. F

    USA made compressors?

    Tom,looks like the sale is over I would of still bought it at this price.Im picking up mine tomorrow at my job were it was shipped.OnceI get it all set up i'll let you know how it is,,,ED
  5. F

    USA made compressors?

    I just ordered a Quincy 5hp from nothern 100 off and free shipping 2 stage did not get it yet I will let you know, it ran about 1300.
  6. F

    School me on tube heaters

    I have a pole barn 24x30 10ft ceiling well insulated I want to go with propane tube heater.For those that have them how are they working for you?How is the cost with propane? I'm looking at a mr heater 10ft 45,000 btu and want to mount it in the center of garage your thoughts.Im in new york...
  7. F

    Complete Hydraulic 4 post lift - failed to deliver product

    Sorry to hear that I got one about 3yrs ago and no problem right on time and lift has served me fine you just never know...ED
  8. F

    Any info on a lean to or overhang on pole barn

    I have a 24x30 pole barn and would like some info on putting a overhang on one side for storing firewood some outside tools and such.Just don't know how to atach header to the metal on side of building being its not flat.Anyone with some pics or ideas if they did this before...Thanks...ED
  9. F

    Compressor and sandblasting

    The one I have now is 25gal
  10. F

    Compressor and sandblasting

    I'm ready to get a new compressor.my craftsman putting out 6.8 cfm just does not cut it with my blasting cabinet I can go about 5 mins and its done.I looked over a-lot of the old posts on here for a clue of what to get.I found this Ingersoll rand model SS5LS 5hp 18.1 cfm 60 gal tank for 879 with...
  11. F

    Insulation in pole barn roof

    I have a 24x30 pole barn,I have put foam board insulation on the walls and plywood over it.I was going to close of the ceiling and put insulation above it,but I really like the storage it offers me.Is there a way I can insulate just below the metal roof with foam board or another type of...
  12. F

    Propane cost

    I wish I had some of your prices I was thinking of a garage heater tube heater I called for propane prices around 3.89 to 5.99 I'll have to re-think this at that price way to costly to heat.No natural gas by me.maybe I'll have to go with something fueled by oil..ED
  13. F

    Help me with my heating choices

    Would like to keep at about 40 and kick up when needed,insulation not great 2in foam board in walls ceiling to be done..THANKS
  14. F

    Help me with my heating choices

    I have a 24x30 insulated garage that I'm getting ready to look at heaters,I have a budget of about 1000 to do the job,I can do the install myself.I was all ready to get a mr. heater tube heater 10ft I would have to run propane as my fuel source.But I hear that they really use a lot of propane to...
  15. F

    Help with condensation and ceiling

    hudson valley,ellenville
Top Bottom