Search results

Hi All, I have a GE CR306 motor starter. 115v coil, single phase, 220v switched - used to run a compressor. The starter has 2 tabs marked 'LIFT' on the coil - can someone tell me what those are for? also I want to drive this with a pressure switch - suggestions on wiring? Thanks Ray

Hi All, Looking at SO KRA (Classic series, I think) and MATCO 5s. Both are roughly the same price, both are ~72" wide. I WISH that they published metal thicknesses etc, but can't find that. Thanks Ray

Assuming roughly the same price which is better built? Thanks Ray

Hi All, I need a very good angle torque wrench. Don't want to buy new, so looking on flea-bay & Craigslist. My question is how does one differentiate the versions/revisions/generation? What about the angle dodad thing-a-ma-bob that acts as a pass through with some sort of angle gauge - how...

Tire balancer? Thanks Ray

I need to remove / install large width tires (have machine). Looking for a good tire iron to complement the OEM one (hunter) that has some sort of drop center. Large is defined as 315mm widths... Any recomendations? Thanks Ray

Hi All, Just as you thought that this horse has been as beat as it could be... I need an OBD scanner. I would like something that ha bidirectional capabilities... That said - I do a lot of work on Porsches, Subaru's, Nissans, BMWs, and a handful of other Asian cars. So 1st problem the only...

Hi All, Been trying to rebuild a Quincy 325 compressor, and found that the cylinders are junk. Turns out that it sat for a while with water or ?? inside and bad rust and pitting set in. So I need either a newer / different cylinder assembly or oversized pistons... Fail either of those, I may...

Hi All, Looking to pick one of these up , but would like the service manual... Thanks Ray

Hi All, Does anyone have any information on a Ammco 400 (sl-400) cylinder hone. Ammco does not have any information anymore, and I want to put new stones in it... Thanks Ray

Hi All, Couple of years back I scored a Quincy 325 pump with motor and a 340 with pump and motor for $150... Gave the 340 away since I would be hard pressed to run a 7.5 HP 3 phase motor and kept the 350. Question is: it is a ROC 7 and I have not been able to find a manual for it... Would...

Hi All, Can someone tell me who makes these bins - they are found in hardware stores in my area... I need some dividers for them... Thanks Ray

I am selling a very old Proto 1/2 torque wrench - still works fine, not been calibrated in??? Good condition Thanks for looking Ray

Hi All, I picked up a 1/2 Proto torque wrench - It is a model # 6016-G. It also say Size-3 Livermont on it as well as Los Angeles on it. Any info on the date and if it is worth getting this calibrated or not... TIA Ray

20-30 ton range. Husky kinda ***** (at least mine does). This is for my press. What brands do folks like? Thanks Ray

Hi All, Part of a package lot I recently picked up. A little big for my needs, and I want it gone and would prefer to not scrap it. Was used until recently... This is a 340 V32, the motor is a 10HP 3 phase and this thing is a monster... Specs can be found here...

Hi All, I am running a 100amp sub-panel in my basement, 2-2-2-4 AL wire as the feed from the main to the sub-pane. The feed is fused at the main panel with just lugs at the sub-panel. My main is a SquareD box QO (NOT the Homelite version). The question is: I don't have any connection points...

from: http://www.techlinecoatings.com/hi-performance/bs-exhaust-system-coatings.html I am thinking of using some of their stuff on my new turbo... Thanks Ray

Hi All, anyone out there re-wire their MAXJAX for 220v? I am wondering about the relay that they use, and if it is usable @220V, or should I rip all this out and install a real motor starter... TIA Ray

Hi All, I just got my MAXJAX and I have a quick question. I mounted the Flow Divider and noticed that there are 2 ports marked 'input' - top left and bottom right- looking head on (unit is bolted to the cart). Does orientation matter for this? TIA Ray