Search results

Looking to install utility style wall cabinets above our washer / dryer in our laundry room. Preferably 16 inches deep. Looking for some recommendations that are a balance between price and quality. Preferably painted white.

Looking for recommendations on spray foam insulation contractors. I would prefer to reach out to companies people have worked with / had a good experience with. I’m in southeast Michigan, so if you’ve used a company and where happy with their work please share their contact information. Thank you

Planning to finish the inside of my garage walls with plywood. Looking for some advice / feedback. Details below. General Plan Information Plywood thickness. Planning to use 1/2 inch thick plywood. Plywood type. CDX is $22 for 4x8, 1/2” thick BCX is $37 for 4x8, 1/2” thick Leaning towards...

- I have a 22x32 detached garage located in southeast Michigan. Probably built in the 1950s. - The foundation is on a concrete slab with a footer. - The framing / wall plates sit directly on the slab. In other words the wall plate and the rest of the garage floor are on the same plane. - The...

1. The sub-panel in my detached garage is a surface mounted box that the previous owner recessed into the wall / flush mounted. 2. I want to bring out the sub panel box and remount it so it’s surface mounted. At the moment it doesn’t look right with the wall panel in place. 3. Question, the...

I have a few problems with the gutters on my detached garage and looking for some advice on the best approach to repair. 1. Broken gutter hanger clips and on the one side of the garage the flashing doesn’t overlay the gutter. See photo below. I plan on purchasing some replacement gutter...

I have a few problems with the gutters on my detached garage and looking for some advice on the best approach to repair. 1. Broken gutter hanger clips and on the one side of the garage the flashing doesn’t overlay the gutter. See photo below. I plan on purchasing some replacement gutter...

Plan on making some repairs to the fiber cement siding on my detached garage. Problem 1. Not enough ground clearance between the bottom edge of the siding and ground. About 2-4” of ground clearance depending on where you measure. See attached photo. 2. No Z flashing to help keep moisture out...

I plan on painting some shutters and doors using a harbor freight LVLP air spray gun. The paint is a latex paint. What's the best way to clean the spray gun to avoid clogging? I assume tear it down and clean with hot water and dish soap? Should I also fill the canister with soap and water and spray?

1. I'm looking for a tool that I can use for edging. The current Ryobi 18V Trimmer I have is good for trimming around the fence line, trees, obstructions, etc. I need a tool that is good at establishing a nice easy edge along the concrete walkways / driveway. Trying to do it with the current...

I recently put up a sunshade umbrella that glides on two cables. I need to attach a hook to the back of the house so I can hook the umbrella to it and help it stay in place. Otherwise, the umbrella slides away over time. Looking for a hook with a plate that has 1 screw hole (not multiple), or a...

Looking to purchase a garden hose that is easy to maneuver, doesn't constantly kink, etc. The hose I currently have is a cheaper vinyl hose that is very ridged, hard to maneuver, constantly kinks, etc. I do use a hose reel so I'm sure that doesn't help (due to the memory of them being rolled...

I have 20x32 detached garage. I am in Southeast Michigan. The garage has a hip roof. I'm wanting to finish insulating the garage by spray foaming the roof deck. Below are some questions and concerns about this method. Any help answering would be appreciated. 1. Is closed cell spray foam the...

I recently purchased an overhead storage rack for my garage. Before I start installation, I want to make sure the ceiling is capable of handling the weight load. The instructions for rack say, "The joists must have a minimum 2” x 6” (standard lumber) cross section, 24” (or less) apart, with at...

I have a hardware cabinet with plastic drawers to store smaller hardware like screws, nuts, bolts, etc. I don’t have a good system for storing and organizing what I’ll call larger hardware. For example, casters, metal brackets, extra hooks for hanging heavy items, cabinet hardware such as...

I have a detached garage. I've insulated the walls. I still need to insulate the ceiling. The problem I have is that the spacing on the ceiling joist (horizontal surface that is parallel to the ground) aren’t standard. Please see photo for example. The gaps are pretty significant, so standard...

Looking for recommendations on a rolling tool chest. Something with a decent amount of drawers. No more than $500. Any recommendations would be appreciated.

I have a breaker box in my garage that is somewhat recessed into the wall. I’d like hide the gaps around the box. Can I cover these with 1x2 wooden boards? Is there another aftermarket solution to this problem? Looking for ideas. Thanks

Currently finishing the inside of my garage. The walls are just about done. I’m doing the install by myself. Looking for ceiling material. Something affordable and easy to cut and handle (not heavy). What are some good options? 1/4 Plywood, OSB, PVC, other ideas? Thanks

I have a 243pc mechanics tool set. The set includes various sockets, ratchets, wrenches, etc. The tools have their own plastic trays. The trays are nice in the sense that it helps me keep everything organized. Problem is the trays are wide. They require wide drawers. I have a mechanics tool box...