Search results

A recent thread on 12V test lights reminded me of this load tester I put together. It’s inspired by the Lisle 28800 that applies an 800mA load and displays volts. For this one, I used one of the many “waterproof battery meters” found on Ebay and a starter relay from a 1980’s Dodge I once...

I’m in the process of getting quotes on a replacement HVAC system. Of course the installers all “generously” include haul off and disposal of old equipment. Since thieves obviously see enough value in a condenser to steal one I’m guessing the scrap value must be more than pocket change. I...

I own this crimper and think it’s the best in my fleet of crimpers which includes Pressmaster and Knipex. It’s for uninsulated barrel terminals. Not sure what the negative reviews are all about. The one review (in German) is for a different crimper. It’s the only small form factor crimper I...

This topic has been beat to death on internet forums since the days of dialup but a Google search didn’t turn up a clear answer to my question. When 7018 rod is stored in an air tight plastic rod tube, in a climate controlled area will it eventually deteriorate to the point where it doesn’t run...

Is this amount of rust on the coil end plate normal? This is after 3 seasons of primarily A/C use. The unit works great, no other issues. I only noticed because I had it apart for cleaning.

Feathering may not be the best term but basically I have noticed there are certain spots on the dial where Autoset jumps to a much higher voltage/speed with only a slight movement of the knob. The dial is only marked in whole numbers but if you picture moving from a position of say 6.9 to 7.1 a...

I need to replace my 30 year old Hoover Portapower vacuum. I like the size of the Portapower and the cloth bag. I use it as a mini shop vac and it handles 90% of my garage/car chores. The current version of the Portapower has mixed reviews so I'm looking for alternatives if there are any out...

I'm re-configuring an older Square D breaker box that uses QO breakers. In the process of looking for new breakers I noticed a bunch used breakers on ebay listed as "black face" or "yellow face". I thought a google search would turn up the difference between the two but the black or yellow...

Looking for some sort of inexpensive signal generator that I can use to check the calibration on an old (12V) automotive tach. I'd be happy with just checking a single reading like say 3000 rpm. Since the tach signal comes from the negative post of the coil I understand there will be a...

I most likely own a SDS drill at some point down the road and I’m thinking to buy one now for a project that probably doesn't justify it. (But of course this is GJ so no tool purchase truly needs to be justified) I have a bunch of 5/32 holes to drill in brick and was wondering if an SDS is...

I’m planning to replace some cedar trim with Smartside composite boards. For those that aren’t familiar it’s basically an OSB type product molded with a cedar grain pattern and available in 1x2’s up thru 1 x12’s. It reminds me enough of OSB that I’m still not fully convinced it’s good for the...

Looking to replace several 200w incandescents with corn cob LED's. Is this a product that's ready for prime time? One reviewer on Amazon mentions using them in pairs to avoid "bands" of light. Another describes flimsy construction. I noticed Home Depot carries a 300w incandescent...

A search of GJ brought up exactly two threads containing the term R421A………I’m guessing it’s not a popular conversion. Is it just not cost effective?

Looking to upgrade my cheapo 48" level after finding out the hard way that the plumb vials aren't very accurate. Both Sola and Stabila get decent reviews on Amazon. It won't be for professional use but would like to hear feedback from the pros on these two brands. For Sola I'm looking at the...

I'm attempting to repair a shower floor that I believe to be a thick bed mortar type. Thick bed mortar wasn't in my vocabulary 24 hours ago but after comparing with some google images I'm pretty sure that's what I'm dealing with. It's over 30 years old and has 1.25" square tiles that are just...

Obviously no tools in Prime Pantry but I have several $5 credits to burn as the result of tool purchases. From a causal glance the prices didn't seem that great to me. If there's a particular category in Prime Pantry with competitive pricing please post it here.

I'm trying to find some brush-on dry film lube with moly similar to Dow Molykote 321R. I'm finding plenty of aerosol offerings but nothing in brush-on. Dow sells 321R as brush-on but $65 for a small container is beyond my budget. I've also found moly paste but I need something that will dry...

Looking at couple of corner clamps. I seldom work with anything over 2" square tube so I'm leaning toward the Bessey or Wilton below. Jaw height on both is 1-3/8" - is that adequate for 2" tube? Any reason to chose one brand over the other? The Bessey is made in Germany if you believe the...

I need a floor scraper to remove the remnants of some foam backed carpet on concrete. I'm dreading this job so I want to buy the best tool for the job. From my brief online search I found scrapers that look like they have replaceable razor like blades and those that look more like heavy duty...

I've been shopping Lowes and Home Depot discounted gift cards on several of the exchange sites. It seems most of these sites have their fair share of negative reviews, but I suppose some of this just comes with the territory. Anybody have firsthand experience with ABC Giftcards?