Search results

Well I'm beginning to develop a plan, at this point I believe a cross draft design will be what will work best for my arrangement. I also found this link which was also very helpful... http://modelpaint.tripod.com/booth2.htm Based on the 100 FPM figure and the booth size of 10'x14', it looks...

Nice, that was informative reading. Now for my next question, the booth basics .pdf used a simple draw through design for it's examples, can someone list some of the different types of booths and the advantages to each design? As far as practicality, a draw through design would seem the...

Well, the purpose of the room is for painting the cars but if I have large parts to paint I would use the room as well. I was looking at the explosion proof fans, I did see that they are very expensive, but don't have much of a choice there unless a good used one could be found. Steve

I'm searching for ideas and recommendations on how to design the ventilation system on a paint room that I am planning. It will be a 26'x14' 10' high room constructed in a corner of my building, it will be used for hobby use painting cars & parts for myself. I honestly don't know where to...

Some very good points from both sides of the coin. After considering all the comments, I think I will pay for the install. I am excited, I've been wanting a lift for a long time!

I'm trying to decide if I want to pay to have this lift installed or tackle it myself. Installation is $450, I consider myself capable of such a task, but is there any reason I shouldn't do it myself? The fact that it is going to be supporting a car over my head does make me nervous about it...

Thanks guys, I'll wait the 30 days, don't want to take anything for chance when putting a car over your head. Never had a lift, I'm sure looking forward to it!! Thanks, Steve

Didn't really find an answer through searching, I'm guessing 30 days minimum. It's 5" 4000# with fiber if that makes any difference. I'm looking to put in a 2 post lift asap. Thanks! Steve

Hopefully this is a easy question... is it a problem if where you are looking to put a lift is in an area that the floor has some grade to a floor drain? Thanks, Steve

Thanks. All that I could find was the suggested retail, and I did see that the A7 was only a couple hundred cheaper, I would spend the extra money for the System 1 as well.

Nice lift! After a quick internet search, I didn't see any dealers listing prices... mind if I ask what it cost? You wouldn't by chance know what the A7 sells for as well? I'm jealous!

Thanks for all the great info, mine would be a "drain to air" setup as well. That trench drain is a nice idea also. I'll have to look at their products. A lot of helpful people here! Thanks, Steve

How much of a grade (not sure if that is the correct term) would you use when digging in garage floor drains? How deep should they be? Thanks, Steve

I appreciate the advise, I had previously decided that fluorescent was the way I was going, but I ran into these metal halides. Six it will be then. Thank you much, Steve

Only 6... really? What were the distances you used to space them? Thank you! Steve

....and I'm sure it's not going to be an average unit!

It's a steel building, 40'x60'x16' with a 2/12 pitch. Its insulated throughout with the white vinyl insulation. I couldn't find my exact part number on their site, I have sent them an e-mail with the number right off my light and I'm waiting to hear back from them. They are multi-tap, I...

On the data plate, its giving an amp rating of 2.31 when running them on 208 (these are multi-tap), so at 120 I think this figures out to 4 amps. I'm leaning towards only running three to a circuit running them 120v, that way I can really be particular on how many I have on at a time. I gotta...

Hmmm, you know I wasn't even thinking to run 3 across the 40', but now that you point that out, it only makes sense. These are 22" open bottom with the clear (glass?) reflectors. I was kinda bummed that they turned out to be high bays (I'm not knowledgeable in this area), but for the price I...

Should I just space them out evenly?