Search results

I own a 56" harbor freight and I am happy as it is at my busy work... But I has masterforce 36" box at my garage to hold long tools.

Is menards near by you than harbor freight?? I do like masterforce box as I own one (36" full wide drawers).

I keep all junk tools as use it if I need to modify to make it easy to do or keep it to be trailer tools if something happen and I has back up tools to use.

Trusty cook hammer- one old tech has one and beat it a lot. Still strong for long time! It had a Indianapolis, Indiana stamped on handle. When I found out it was location near my parents home, I had my dad stop by to pick up a dead blow huge hammer like 12 lbs as best one I has use to get big...

Menards sell that lights and few items plus power washer!

I would like to compare with bostitch standard flex ratchet to snap on ff80 as compare 72 teeth to 80 teeth, 24 dollars to 114 dollars. I may talk with my snap on guy about ff80 to see if he has sell it.

I has china and Taiwan sockets and ratchets like Stanley and bositich (ratchet). So far I has no problems but sockets start to show wear and swell a very little. But I use same sockets everyday as work for ford but Chrysler and GM too as used vehicles...

I has sockets up to 1-1/2 and to 46mm. I use those often. Even I has 29mm to 39mm 12 points.

No. It is not adjustment. But you can cut the metal sheet and fit on to make what you would like to do...

Umm... I would like to use that as for remove the torque convetor bolts or nuts on ford as I has do engine swap am sometime I can't get thin ratchet and super shallow socket to fit in. I can use craftsman deep offset box end wrench but warranty time paid are **** so I want speed up..

I did had my Mac tool dealer called the Sk tools company about this. They said they are plan to make new design and sell in middle summer of 2014... But it would be good for me to use at my work that I has to use offset wrenches often... I am still not sure should I order it from amazon.com or...

I can find a special tool for other way if I can..

It was said for fuel filter on import vehicle but I got it for ford ICP and other sensors that require 1 1/16 socket but this one is semi deep and fit in good.

My work have two service dept as one is general service and other one is heavy line service as diesel, engine, trans, etc. I am in heavy line as my work want me to do that. I will do almost all works except not a noise like nvh or wind noise... Not worth to waste my time!

There is techs at my work are "specialist" which they has limited tools to do because they may don't want do what I could do since I am heavy line tech..

I can't make a tool list as I own a too much tools and multiple boxes at largest ford shop... You need big sae wrench as 1-1/16, 1-1/8, 1-1/4, 1-5/16 wrenches. I went overboard on tools but it help me to get repairs easier and get me out of troubles.

Whoops.. I did not think about use search thing..

My dad and I was looking at harbor freight ads today and noticed the harbor freight sell a top chest for that 56"bottom box... That is interesting since harbor freight had statement that it would not "support" top chest??? Now they do sell.... Is it for new model, not a old model??

Oh I see that. That is a lot of issues you had with blue msc750... My msc750 do good job for me even too much tools in each drawers. I was plan to get a snap on krsc serie as 40" wide but Matco guy gave me better trade in value on older Msc4 so I traded it in and paid cash for it. All...

I has same msc750 as your one. I love it.... I had no problems as it was demo on tool truck for while.. So I got it and love it. What is wrong with old one? Slides, drawer or lock problem?