Search results

Sun model 200 tune up analyzer and oscilloscope and base cabinet SUN 003 by skipskip, on Flickr SUN 006 by skipskip, on Flickr SUN 013 by skipskip, on Flickr More Pictures here: http://www.flickr.com/photos/skipskip/sets/72157633937154647/ The SUN 200 was an entry level model...

Just got an older garage jack, it uses a ratchet and chain system to raise the car. Any ideas who made it? I'm guessing, pre WWII? may 056 by skipskip, on Flickr more pics at the end of this set: http://www.flickr.com/photos/skipskip/sets/72157632821088755/ thanks Skip

Bump for new lower price $25 , you pick it up ARO 3 reel set Air, Grease, Oil My guess is this dates from the 60's but I.m not sure. all three reels are there along with the housing it does NOT include the pumps or barrels. the housing has been painted at least once and the decals are...

I need to run some outlets down one wall of my garage. very old wood building with no insulation or inside walls, just 2 x 4 with siding I need 2 inside and 2 exterior. can I run one line for all? or should in and out be separate? Exterior need to be GFI?, interior also? what do I need to...

here's a link to an article about the worlds biggest conatiner ship http://gcaptain.com/cma-cgm-marco-polo-master-and-chief-engineer-on-what-its-like-to-command-the-worlds-largest-containership/?utm_source=feedburner&utm_medium=feed&utm_campaign=Feed%3A+Gcaptain+%28gCaptain.com%29 my...

I was reading a thread here last night saying that someone needed 4 minutes with an air impact gun to loosen a nut. I usually try my impact for 15 or 30 seconds, and if it doesn't come loose I assume it ain't gonna, then I try something else. Will long term impact gun use on a stubborn nut...

Our ancient thermo-pane window has lost it's integrity. whats on the market that is more energy efficient? or better in general? Just a large rectangular pane , about 5 by 4 feet thanks Skip

I have a steam kettle, for restaurant. Basically it's a huge double boiler with a huge heating element in the base JUN 227 by skipskip, on Flickr The Id tag says its 208 volts 3 phase JUN 229 by skipskip, on Flickr I understand that 3 phase motors need to have a converter to run on...

I have a chance to buy a 30 pound can of R12 at a reasonable price. How do I tell if it is full? what does the 'seal' look like what will a full 30 pound can weigh? How do I tell if its actually R12? Any other advice? Thanks Skip

I believe this is a number 14 set. Includes box and 10 6p sockets 7mm - 15mm + 17mm 13/16" sparkplug socket 1 1/2" extension (SK, but NOT SK WAYNE) 6" Extension Ratchet tools are good users, but have some signs of use, this is not a set for collectors box has quite a bit of 'tool box...

My neighbor and I disagree about this he says its fine, I say not. opinions? Skip

I have a used Curtis keycutter with about 75 aftermarket GM blanks. I also have the code book the cutter will cut other keys, but you will need to get the correct blanks for them, I only have GM blanks Pictures here: http://www.flickr.com/photos/skipskip/sets/72157629096442546/ $75...

Several times recently I have needed a Torx tool smaller than T10. I don't know which ones, since the screws are too small for me to see, much less measure. anyone have experience? handled tools? sockets? set? I don't need top end tools for this, but a $1.99 Chinese set wont be good...

Another thread was asking about a winch bolted to the garage floor, which reminded me of a similar project. I need a 'dead man' at the end of my driveway to winch cars toward. I was thinking of a phone pole, I could use it for a light pole and mount an outlet on it. how deep to plant it...

Six used wheel nut sockets SOLD All have been used, these are not for polishers, work fine, look used. $5 each or $20 for all six, plus shipping paypal preferred, ck/mo OK all are 3/4 drive Proto are the cast ones P1909 3 1/4 P1913 3 7/8 P1919 4 7/8 steel ones are OTC or BWP BWP M1914...

Some of us use heavy duty fixtures in our garages, so here are some HD bulbs. most are new, but some have been used,hard to tell on the gas bulbs, because all of them have black around the lower glass. I have tested the incandescents, they all work. I cant test the others as I have no...

I have some odds and ends of snap on to sell. I cant get along with the pic editor here, so pics are on flickr here: http://www.flickr.com/photos/skipskip/sets/72157628071214774/ first is a pile of hurt snappers: XB2426 DBE 3/4 x 13/16 real bad finish OEX-16 comb 1/2 kinda bad finish...

A pair of Gits Brothers oilers 1/8 pipe thread. poly bowls are dirty, but these seem unused. $25 for both shipped to US PayPal or Check or Money Order Thanks

SOLD!! THANKS one F710R, 1951 date code ,small patches of finish wear works nicely, this is a pretty rat. $25 one F70R either 1950 or 1960 date code, I cant tell for sure. It has a fair amount of plating wear, selector broken, screw missing. You will be able to make this one work, but...

Sold these are two sets of tools for working on lock cylinders. $50 for both, free shipping to the us