Search results

I wouldn't worry about the 5psi. but if you are just drop the pressure switch on the compressor to 140-150psi and call it a day! You just need to open the pressure switch cap and loosen the spring tension nut. One of the spring is for the start(adjusted to let say 80psi) and the other is for the...

seems a bit high compared to what I have been quoted for a 28x44 in Drummondville. But everything is pricier in Montreal itself.

blast it with wallnut shell. (Like sand blasting but with crushed wallnut shell media)

if she can make it to styrofaom, I don't see shy you couldn't do it to wood.: there's plenty of "faux finish" tutorial around...look it up

Craftsman was in their own while under sears. Now they are from Stanley/Dewalt(Who bought Craftsman from Sears), so they are the same tools, with a new red color instead of yellow. Comparable for the price range.

I'm pretty sure he talk about a mini-split when he say "through the wall"

I'm in the same situation. I have calculated a 3'x3'x12" pad where the lift is gonna be. and pex will go around that pad. vapour barrier under the foam (I use Hydrofoam for simplicity of pex installation) with fiber reinforce concrete. No foam under the pad as foam can compress a bit. For the...

Re: Minimu garage size? 26' is the outside of the building. here in canada we build in 2x6. Add sheeting, strapping, exterior and interior finishes, and you lost 8-1/2+" in each end. that make the inside to ~24,5'. I don't think a 1,5' gap each end can be called "several feet clearance"...

Re: Minimu garage size? 24 width is great and wide enough...but 26 deep can be a bit tight with a truck. My supercab 6,5' bed F150 fit kinda tight in my old 26' deep garage, and I only had a smallish table on that wall. If you plan to not put anything on the end wall...26' is good.

tapcon or expanding anchor.

3-1/4 is common my dad is selling pneumatic nailer nail and staple for 30years and 3-1/2 is not readily available nowaday. some client have always used that in the past and were still asking for it, but they all went to 3-1/4:| might be possible to have an order done but it would be at...

Regular hair dryer will do the trick to soften the glue and peel the sticker. What you don't want is to remove the sticker and leave the glue there. it's a PITA to remove. To remove the glue residu (whatever you do, it's 100$ sure there will be residu at least around all the edge), you just...

I see no issue except maybe the floor finish....but other then that, can' be worst then a concrete driveway.

Most cheaper one : the pump won't lasst more then a couple minute with solvant. But nowaday you can get very good water based stuff....but need to be heated. I fitted a 120v 1500w water heater element in my tub. it take about 20min to get it to temp (40-50C) and it work great!!! the flow...

there's no way you should have to shim 1/2" to have the post come inward 1-1/2" at the top. Plus would care about the level of the base plate....it's the post that need to be leveled and the base plated shimed the less possible (at least one corner shouldn't have any shim)

I have water a 6' underground but don't care about watering my lawn

Adam Savage wire spool. You can glance at it a couple fo time int he video: look at 12:55 on top of his "cabinet"

simple 2x4 or 2x6 are way enough to run over with a car. My dad have a pit "hole" in is garage (which have a full size basement under it) and the pit have a notch so the 2x4 end flush with the floor (and a valley for water drainage). He park is car over the wood everyday. 2x4 and 2x6 are screw...

just repaint it. to make it clean. No coating wil give value really :|

I'm building a 44' deep and lift is gonna be as close as the door possible. 13' as per many 2post symetrical lift manufacturer I saw and should fit a crew cab short bed. I couldn't care less about not being able to walk behind the truck when on the lift or lifting a long bed. The rare...