Search results

While expensive, I don't think you can't get one better. I use it all the time to set 1/4 window regulator and door handle rivets. They also sell a manual version of the same gun. But air is the way to go. Sent from my SM-N920P using Tapatalk

I had one installed in a metal carport garage. Seems like a good quality door. Mine has an external padlock sliding lock. So no way to open it from inside. Opens and closes easily. Mine is a 10 x 10 door. Sent from my SM-N920P using Tapatalk

I out about 2 foot of blacktop on the gravel side of ours. Keeps the rock of top the drain. What does manage to get in there, you can pull the top off and clean it out. Sent from my SM-N920P using Tapatalk

This what your talking about? If so yes that would solve your issue. We had this installed and the drain went to daylight in the lower part of the yard. Sent from my SM-N920P using Tapatalk

I had a 30 pound lp tank that was used as a portable air tank. Worked OK. Sent from my SM-N920P using Tapatalk

I saw our shop compressor break the welds of a couple of the feet bolted solid to the concrete. We installed the new ones with a rubber cushion and just a steel pin sticking up out of the concrete into the hole in the feet. Sent from my SM-N920P using Tapatalk

I bought a used repo snap on torx set 15 years ago for payoff of the guys bill. I think I got the whole set for $75. I then had them put new bits in all of them. Been going strong since. Sent from my SM-N920P using Tapatalk

If not fastened down yet seek a local votech carpentry or mill and cabinet program and see if they will run it for you. Little to no money. They have the equipment and labor to get it done for you. Sent from my SM-N920P using Tapatalk

I agree, shop around. I do a 3 year lease but the lease fee includes the first fill. But my local gas supply only keeps their bottles on hand to trade. If you own it, they have to send it away and bring it back a week later. Lease customers just switch them out. Sent from my SM-N920P using...

I have a Sharpe f88 water separator filter I've been using in my body shop for about 20 years and is still going strong. Sent from my SM-N920P using Tapatalk

I'd be all over that deal! Sent from my SM-N920P using Tapatalk

Now that I think about it, I can't remember when I bought mine but I ordered it online but picked it up same day at the store. So it could have been a leftover deal. It was a couple years ago. But I could be wrong on that as well! Sent from my SM-N920P using Tapatalk

I picked up my last one up in store off the shelf. Unless it was an online return. Sent from my SM-N920P using Tapatalk

That's the beauty of their system. I needed a Cordless hammer drill, so I bought one of the old blue 18v 2 speed hammer drills for cheap on ebay and runs great with my li-ion batteries. Sent from my SM-N920P using Tapatalk

If you watch home Depot, sometimes they have the big 4ah li-ion batteries with a "free" one in the pack. $99 for 2. Sent from my SM-N920P using Tapatalk

The new charger will also charge the old nicad batteries too. Or at least mine will. I love the one plus system. One battery for everything. Even upgrade old tools to new tech in batteries. Sent from my SM-N920P using Tapatalk

If you have a velcro orbital sander, stick a red scotchbrite pad to the bottom of it. Sent from my SM-N920P using Tapatalk

I have an old 10" craftsman regular miter saw. I let someone borrow it and they broke the locking pivot handle off the front. I just had the deck welded at 90° and its only used for square cuts like wet deck boards and the such. Sent from my SM-N920P using Tapatalk

Care to share how you got it for $389? Sent from my SM-N920P using Tapatalk

I have an old kitchen counter for a table top in my shop and wanted to make sure it would fit. My old slider wouldn't. That is 24" if I'm not mistaken. So I should be good. Plus I have bare studs, so I might get it back into the stud bay some. Sent from my SM-N920P using Tapatalk