Search results

Hello, I recently acquired a Quincy 20 gallon air compressor and need replacement wheels. I ordered a few from a few sources and the quality all ****, really bad. I have an old devilbiss compressor tank and ended up taking the wheels off of it. Both the Quincy and the DeVilbiss wheels have...

Can anyone tell me what these 2 pieces are? I recently acquired this saw and I can't find their mention anywhere in literature. The saw dates 1961 as far as my research, model 103.22180. Not sure if I'm keeping it yet, like the look, don't like the small table. Thanks for any help!

Come help me clean out my garage. Most of this stuff would be local pickup, unless a creative way was found to ship it. Vises Reed 4C $750 Its complete. NEW jaws from wiltonviseparts.com (member KMScott on the board) Prentiss 20 (2 of them) $30 SOLD! and $100 Swivel rear jaw, swivel base...

I have accumulated a few too many vises in my garage and want to see them go to a home to see some use. I have a couple parkers, Morgans, Prentiss, and athols under 5". I also have a reed 4C and a reed 1C. Prices vary but all under $100 except for the reeds. I have $750 into the pair and would...

I have 2 Witte hook and pick sets available, straight from Germany. Very high quality, it's what I use personally. $40 each shipped priority in U.S.

I have a set of Snap-on E4 - E18 and T27 - T55 (including the GM T47). $60 each shipped to you. Very nice condition. These were sets I had at home, no longer working in automotive and new job doesn't need torx, so i'm sending these down the road. Both are SOLD

I have an 8 piece set, very lightly used, some haven't been used at all. $110 shipped + paypal fee if applicable 4 flat 4 phillips

I need to purchase an insulated screwdriver set. I am torn between Wiha and Witte. I have used Matco (rebranded Witte) stuff before and like them, but people seem to recommend Wiha the most. I am assuming thats because they are slightly cheaper and a little easier to come by. Who has either...

I'm looking to buy a mid rise lift. I have used Challenger lifts in the past and they've been great (regular car lifts). So I am looking at the Challenger MR6. However, the more I look at all these lifts, Challenger, BendPak, Titan, Dannmar (northern tool), even HF, they all look the same. I...

I've been looking to get a trans jack, and have been doing some heavy research. First looking through reviews on Amazon, the Grizzly and OTC 1521A seem to both have good reviews. I want a jack that is a balance between quality, price, and serviceability. I really like the real OTC jack, the...

I have the opportunity to pick up this box. The bottom only. The top is an old MAC. Perhaps I could swipe the top as well, I was just interested in the bottom. What would you give for it? I want it to use in the basement to organize my house tools better. I'm assuming its 50s/60s.

I am in need of a needle scaler. I am looking at the CP 7125. http://www.amazon.com/gp/product/B00AJMPYC8/?tag=atomicindus08-20 Does anyone have this guy, or have a recommendation for a good scaler? HF will not be taken seriously, i've used it and its junk. I wouldn't waste my money on that ****.

I have a Prentiss 264 vise for sale. It is a 4" jaw. Weighs 51 LBS. This was the last produced Prentiss after they were bought by Parker and are actually made by Parker. Check out the photos, you will not be disappointed, this vise is CLEAN. Restore it, lube it and use it, your choice...

Does snap on flat rate repair cover floor jacks and anyone know a price if they do? I picked up a used YA700 USA today and it needs a rebuild. Their flat rate is usually pretty good, so may not be worth the hassle of doing it myself. Also, would anyone know what the walker jack model # is so...

I picked up this Milwaukee Hydraulics bumper jack model 15. I was told by Milwaukee that the model 15 was produced between 1948 and 1956. I plan to eventually do a restoration on it. I think its pretty cool and possibly useful for tire rotations at home.

I am in the market for a quality floor jack. I have looked at previous threads and have come to the conclusion its either HW or Milwaukee. Since I live in Milwaukee I can pick it up and support the home team, so thats what i'm leaning towards. Are there any other brands you would consider or...

Brand new in the tray and wrapper snap on 315SIMMYA 1/2 drive deep metric impact sockets 10mm - 24mm all sizes, no skips. Shipped to you free.

I got burned buying some fake NGK spark plugs. They even came in a Honda box (or a fake one). When I called out the seller, he promptly refunded my money. I spent $1000 in parts rebuilding my Honda CRV engine that the pervious owner severely abused and when it was all said and done I wanted to...

I am looking for some 12 point metric axle nut sockets. 1/2 drive. I want to stay USA made if at all possible without paying snapon price. I checked SK, proto, and wright. No one makes them. Anyone know of another manufacturer, or am I going to have to go with sunex or grey? Thanks!

I recently picked up a pair of vises that i'm looking to restore. For all the experts out there, what is the advantage of electrolysis vs just wire wheeling the metal bare? I assume you have to wire wheel anyways to get the paint and grime off. The ones I picked up, a Prentiss 20 and Morgan...