Search results

Thanks everyone for your replies. I do have a nice size shed for all of the lawn stuff however it's at the back of the lot. The snow blower is in there because of the storm that just passed. The only other lawn equipment is a rake. The stove was purchased by my girlfriend and I have not been...

Like everyone else here, Rockauto.com all the way. Prices are great, customer service is tops, shipping is quick. The only time I go to an auto part store now is if I need the part immediately.

I just got the HF 1500 lb jack. Haven't put the bike on it yet but it does roll around better than the Craftsman I used to have. I have done a full tear down and rebuild of my bike on the craftsman. Haven't found a need for a full lift yet so a jack works for me. I have a rolling seat that I...

How many rolls did you end up using? The garage is looking great by the way. I take it you're off due to weather or is your company having a shut down during the holiday's like mine is?

Where did you get the insulation? I have to insulate my one bay and went to Lowes and it was expensive.

So after many years of lurking, after my divorce, I was finally able to purchase a house with a garage. Not my ideal set up, but it was priced 30% below market and the inside of the house was already updated with new kitchen, bathrooms, living room and dining room. Today, I decided to start...

Autogeek.net I have a flex DA. It buffs as good as a rotary with the safety of a DA. It is not as fast as a rotary but is much faster than the Porter Cable. It is more expensive than the Porter Cable. Edge makes an adapter to use their smaller pads for spot buffing. Autopia.org is another...

Kevin, Thanks for the info. What brand of knives are consider good? Does it matter?

Stump, Thank you for pointing out that it was a 4 year old thread however I needed info and of course you provided none.

Don't mean to hijack this thread but it is along the same lines. What are some good brands of taping knives?

Thanks guys. I did plan on making it deeper than wider. I like having the work bench and tool chests at the back of the garage.

Long time lurker. I am currently looking to buy a house but am noticing a lot of the nice ones don't have garages but have the land to build a nice one. .5 - 1 acres. Location: Northern Connecticut. Question: What is the average cost for the footers and slab? The slab must be able to support...

Can some one email me a copy of the receipt? I looked up store 1060 and it shows it as $79 Thanks

It still has a pressure gauge and I only took it up to 90 psi and then unplugged it. Now I am starting the rebuild. Thanks for the info.

Free is always the best price.

Picked up an old ACME air compressor. Don't know the HP of the motor. It is an oil compressor with a 10 gallon tank. Paint is pealing, placards are covered by crud and hard to read. It is hard wired as the pressure on/off regulator is broken. My question to start is..Are these high/low shut...

Found out that the Kobalt Impact wrench is model 232159. If someone from CT or MA has purchased this at the clearance price of $27.99, will you post your receipt. Thank you.

Iamhistory, What model number is the 1/2" impact? I went to lowes today and bought the 49 piece air set for $47 normally $99. I was looking for the Impact wrench and didn't see any that were 525 ft. lbs. The 500 ft. lbs one was $69.99

I have both by my house side by side. I find that at my location I can find what I am looking for easier at HD and there is always someone around to help. At the lowes near me, I have pushed the assistance button and literally waited 20 minutes and no one has shown up. The times when someone...

Goo Gone and a hair dryer works great. I removed the emblems from my motorcycle's tank using this method. Do not try to peel it off cold and without goo gone or wd-40, it will just rip in pieces and drive you crazy sort of like wallpaper.