Search results

The rooms are separated by a solid wall. One entry door each. No windows. The wall unit fans run for extended periods of time. I know from working on finishing up details in these rooms. Both rooms are insulated. Concrete floors have vinyl flooring. The addition of the tack room converted...

I have tried all 3 speeds.

I updated my Barn tack room and feed room [both12x12] over the winter. I installed a Mitsubishi 24,000 btu condenser unit and 2 -6,000 btu wall units. Installed with no issues. Nitrogen pressure checked for 24 hrs. ,no leaks etc. Heat function worked when it was cold outside and the cooling...

I forgot to mention the reason for the D/SW. is to be able to quickly shut down the Walker from the Barn if something goes wrong rather than running 120 ft. to the shut down button on the control panel at the Walker.

OK,another question about disconnect switches. I am installing a Siemens 2 pole 230v. 60 amp. D/SW. That takes care of L 1 and L2. To be approved for a service disconnect sw. ,do I need a 3 pole so I can disconnect the Neutral. I will add its non fused , and the Walker motor is 30 amp 3...

The RV panel has a receptacle for plugging in a power cord for a Motorhome or a LQ Trailer without using the onboard generator. The one I have has bot the common 30 amp recep. and a 50 amp. recep. along with a duplex recep. I initially thought there was an available breaker in it that I...

Got the RV panel and found out the breakers are for the 30 and 50 receptacles. So I will feed this from a junction box inside above the horse stall using a 3 terminal insulated bug. Need one each for the GRD. ,N , and one hot leg since the RV hookup is 120v.

This the RV panel that I can use as a sub to continue the 30 amp 230v line to the Walker. Should make for a cleaner install.

Found a RV hookup panel from Connecticut Electric that has a couple of breakers in it. I can use it as the tap off to continue the 230v 30 amp line to the walker. Run the feeder wire to it from the main panel. Cleaner and cheaper. I post a pic of it when I can.

A lot of good info here. Thanks guys. A sub panel sounds good but with all the horse stalls, the only location for one is right next to the sliding door. Too close to the outside weather for code? All my runs are above the stalls.At the main panel ,is there a breaker that can take #2 wire ...

Was looking at THHN wire.

The Walker requires a 30 amp 230v circuit. They don't specify wire gage because of unknown distance. I did one of those online calc formulas and came up with 6 AGW. Thought about 4 AGW because I couldn't figure the Walker acceptable voltage drop. Was going to run the wire thru 1- 1/2 pvc. I...

I am running a 230 volt 30 amp circuit to a Horse Walker from my Barn. The run is 250 ft. Going to run off a 30 amp breaker in the barn to a disconnect switch outside the barn, then in conduit underground to the Walker Control panel. 4 wires-2 hots, N and grd. What AWG should I use and...

Wish I had bought a second RJ-45 when I got my 14,000 lb. BP. There have been so many times I needed all 4 wheels up at the same time. And yes, I am not a fan of 2 post lifts.

Nice shop. Those guys really work fast. I would still be trying to get the corners square.

Not lucky .I hot water power washed the frame and blew it off w/air. Have to get the sand residue off. My dad blasted and painted his heavy equipment since the 50's. I picked up where he left off in the late 60's. If I wanted an automotive quality shine on some items, I would have to knock...

I don't think you can get a better prep surface than what sand blasting does. The sand etches the surface really well. You need to wash the sand dust off before painting. In 2003 I blasted and brush painted my 72 Vette frame with POR 15. It flowed out perfectly like as if I sprayed it...

I used my 4 post to pull a 72 corvette body off the frame. Used nylon straps. After the lift topped out I had to remove the rear tires and lower the chassis a bit because the vette gas tank sits high on the frame. Then I drug the chassis out from under the lift and made a frame dolly to mount...

I was thinking about that [ 373P remote ?]. If I understand you correctly , I know I have to hard wire a Smart controller at each door location for each door.

I am getting ready to change out my 3 WD IDrives with the Liftmaster 3800. I have the correct torsion shafts so that is not a concern. I don't want to mount the Smart panels at the man door entering the house in the garage because they need to be wired[bell wire]. I have finished...