Search results

The breaker is a double 30 not sure on the gauge of the wire but after looking@pix the old man had a huge welder plugged into it.The oven was 220 out of my kitchen so just gotta figure out how to hook the wires up

Hey fellas I need a bit of help here &I know alot of guy's expecially real electricians are against guy's doing stuff like this but I think I can pull it off with a little help. So please don't jump on me too bad. So we used to have this outlet I want to say for a welder or for the car lift...

I have a plug for a welder yes, And its just a regular kitchen oven.

so in my home shop its run off of its own a small fuse box, I wired the shop myself including hardwiring my compressor I am hooking up my old stove to do some powder coating IN,how should I go about doing this I also have a plug should I just go and wire that up to plug the maLe end into? I...

Ok so I know tyvek can lock moisture in if used inside & cause mold etc.Well in my shop there is metal behind that felt then osb &on the inside there is the thick foam board the foam is held in place by 1xs screwed into the osb.Is it safe to hang the tyvek on the inside to those 1xs as there...

thanks guys,maybe its not silicone whatever it is says its for metal roofs,well the ice dam would make sense I think,I got up there&it looks like what's frozen @ the front has the melting coming from the top of the roof/pitch so I'm thinking that melting water is hitting that ice & it is backing...

Ok so guesing maybe this is common,but I have a monoslope/ shed roof on my shop when the panels were cut they were suppose to be 38 ft to avoid anything like this but they cut 36 & they were closed the day the guys but em on so we went to opera got some panels set the short 2 ft or so panels...

are you saying like a gable roof garage like my old shop then this part like when people add a lean too?that be huge I was gonna keep running the pitch up,what do you suggest on how the additon should look?

Thanks I just found the reply in the spam box.I talked to the wife & where thinking to builld on & put a entrance on side as I think I mentioned & building a office so customers can quit eyeballing my tools.A 60 ft long x 24 ft wide monoslope is gonna look nuts.I wonder if there is a way that I...

Just need some advice I do paint & bodywork from home in a 24 x 36 monoslope shop.It use to have a gable roof with trusses but that's a whole Nother story so now its like this..hell I still haven't put the corner pieces on but roof is all new lumber even cedar over the rafters,osb all...

Well we live in a very small town I called the hardware store I bought it from&he came by&said loose connections.

Ill check the breakers but I know forsure the wires were not twisted together before he put the nuts on.

Can't really afford to do that my kid brother died a few months ago then I found my father dead then as a result of all of the death my other brother lost it shot a couple guys &was then shot dead so Ive paid for the final costs of my 2 brothers&dad in the last few months & I have some very bad...

This has nothing to do with my garage but I've been doing some remodeling in my home which my grandfather built some 30 years ago. He didn't sub nothing out did the electrical,plumbing,framing,roofing etc etc with him&my old man.Well in the middle of doing this we bought a new dryer which sits...

ok so I have a 24x36 monoslope shop low ceiling starts@7ft runs to 12ft. have the 4 ft shop lights which really aren't brite...but I do buy the cheapest bulbs Lowes sells is there a brighter bulbs I should invest in?I have a box of the porch light type fixtures you know just round and hold the...

we powerwashed,then grinned the floor did the each etc..this is what I believe happended I believe since the storm rolled in&epoxy wasnt fully cured if raised up from the concrete&raised it in those few spots.Its ok however we touched it up the spots we touched up are lighter than the rest of...

I would rather have few or none then some that offer things of no value..because I wrote that I sanded it away so all he would see was where it had been sanded&featherd.I understand if I would of been like "this is doing this I'm not sure why,what can I do?"but since I already mentioned what I...

what do you need to see pictures for?I didn't need anyone to look@it&tell me what they thought was wrong I simply asked if anyone has had peeling due to moisture after coating.So again seems why are pictures needed?

So we went&put rustleoum epoxy kits that they sell @ Lowes it appeared to come out well @ first..wasnt a lot of gloss to it but on about the 5th day..(today) I went down there&it had peeled up in about 4 HUGE. spots .I think that it had something to do with moisture as it was warm when we...

Thanks.Ive never heard of epoxy cement or the concrete weld.