Search results

In my experience, 7 to 10 years

Here's my quick cutting station white wings open on all metal box to control sparks from chop saw. Ratchet handle on base of chop saw lifts saw onto casters underneath so saw can be rolled where needed, then lowered. Hand held band saw cuts great hanging on bracket. Simply lift off and take...

I built a "C" clamp out of 2"X1/4" angle with curved plates and 3/4" all thread with welded nut. Run it down with air or electric impact. I use it mainly to change out tpms air valves. Don't have to remove tire from vehicle to change tpms.

My uncle,who worked in maintenance in a gasoline refinery, put me onto the 50/50 atf/ acetone penetrating fluid ( he called it "panther piss") when I was a teenager. I've used it every since. I'm not going to give my age, but I remember eating honey on my breakfast cereal due to sugar rationing...

Yeah, I didn't go into detail. That's two 120 volt compressors on two circuits going into one 20 gal tank. They are stickered at 4.9 and 4.7 cfm @ 90 psi. I think these rating are high.They are mounted one atop of the other on a frame I fabbed with lifting eye. They are mounted in attic of...

I just order my stuff through my local tire shop. They just add it to their order and mark it up 10%. Still cheaper than online. On my over the road trucks and trailers, I went to the mercury filled balancers ( and some centramatics) about 20 years ago. Still using weights on some cars and...

In the house we have in town, I have a gasoline powered 30.gallon 27 cfm in a shed behind garage. It's plumbed into a 20 gal 120 volt 9.6cfm that's in garage. If I need extra air, I just fire up gas powered unit. Honda engine, remote start.

I put mine outside the back door of garage in the dirt. Dug a 2' hole with posthole diggers. Had a 8" piece of 2 1/2" square tubing laying around and welded 2' of junk to the bottom of it being careful not to exceed diameter of post hole. Cemented this into posthole. Welded 2" square tubing onto...

32 cents a pound, minimum $8 at salvage yards today in Northern CO.

Does anybody remember a ridiculous federal law ( or UL mandate) in the late fifties early sixties that said any rotating power tool could only have a 12" power cord on it? I still have a 3/8" and a 1/2" drill from that era with the short cord. Mandate didn't last long. Thinking was to keep tool...

I have a 30 gal 27 cfm gas powered air compressor mounted directly to the steel floor of my service truck. Over 10 years now. No problems. Doesn't vibrate anymore than the welder which is also bolted directly to the steel floor.

I spray latex with pressure pot. Thin 20-30%. 60-65lbs

Yeah, get that whooping 1/10 of 1 percent interest on the savings account.

X2. Nearly every town has one.

Got any scrap iron laying around? I made all of mine. Think I have four from about 1/2 lb. to 15 lb. Very easy to make if you have access to scrap, a way to cut and weld it.

I have two ac delco bought from eBay. One was $120 and the other was free due to ups losing it for 3 weeks. Seller sent me a replacement and told me to keep the original if it showed up later, which it did. I use every day. Lots of torque. Better have a good grip on it. Don't know anything about...

Comes with everything you need to get started. I just googled it at $79.80. It's a 12 bit device.

Hantec 1008 Run with laptop 8 channels Less than $100 on eBay Works for me

How in the world did "door" get in there. Suppose to be bumper.

X2 on prepainted. 2007 Tahoe $120 to front door from eBay. Perfect fit and color match.