Search results

You can say that again. Granted my grinder is nothing special but with the wire wheel on I can stop it. If I forget to install the spacer for the wire wheel it rubs the guard and may/may not turn on at all. I could use a better grinder but not until the one I have gives out.

If you were Warren Buffet you would be driving an 8 year old Lincoln Town Car with no interest in tools. Ha.

I would buy less and buy higher quality. I would block this site from my computer. Not because I don't like it but because I did everything with basically a 26" top box but now have a full top/bottom and 44 roller cabinet and wonder what I might want to pick up next. 40+ ratchets, really? Yes...

You might be able to find some commercial property that has been sitting empty for a while that will rent/lease cheap that you could use for projects. Keeps you out of trouble at home and avoids building something that over time I think will be more of a hassle than a convenience.

I used them most in 1/4" with hex head screws. I liked putting those in instead of the philips screws because I rarely ever stripped a hex head screw. The main task was mounting hardware on a 3/4" plywood backboard in telecom rooms. That was mostly before drill batteries are as good as they are...

You should be careful what you ask for. They may have blonde dudes working there. On a side note. It surprises me you had so many issues with the Grizzly product. They have been in my experience a very good brand. They make different levels of products but all I've seen so far have been nice...

Now that was funny right there. I would have loved to been there to see that in person.

I have bought from these guys several times and had excellent service every time. I have bought many of my Vaughn hammers from them.

No specific brand but for me I stay in about the middle. Too cheap its useless and too expensive I have over spent. That is a weak answer but basically something that is meant to be used for grinding or scraping I will pay a little more. I bought some cheap Dremel wheels that explode sometimes...

Awesome...graduation photo then two over a picture of bare a$$. I just find that so funny.

I have wanted to install one of these systems for a while now but have never found them to be "affordable" for me. The cost of the panels would have to come out of pocket and with the relatively low cost of power here it would take quite a while to break even. There may be a system out there...

In 98 I had a Honda that I wanted to make faster. I installed an aftermarket exhaust. After a week of hearing a rattle under the car I decided to fix the problem. The car was lowered so that I could not get dads jack under it unles I parked at the end of the driveway where it met the street. I...

I have my HF 44" under my workbench. I took the wheels off and set it on a 1/2" piece of plywood to keep it off the concrete. I lose a little space to the back but in my garage there is a ledge that runs around the outside that prevents you from pushing all the way to the wall. Anyhow, it keeps...

I have been looking at one of the little Husky units at the Home Depot. I have a bigger unit but thought one of these little compressors would work fine with my nail guns. Nice thing is its oil lubed so it should be fairly quite and the reviews are good...

The problem for me is it would cost a grand to see. My need for light has really increased over the years. Ha.

Sounds good. My last set was a Ford Explorer. I replaced the whole arm on the top and like I said just popped the bottom out with a hammer leaving the arm on the truck. Pressed in the bottom with the rental tool from Autozone. Overall both sides went quickly and led to the discovery of worn...

We use tubes. Pull and patch the tube when needed then toss and replace after too many patches. Keeps the interior clean and easy to work on.

Lower ball joint? I remove the clip and hit it a few times with a hammer and it pops right out the bottom. Press the new in and put the clip on. Guess I do it that way because I don't have a press.

Real men use cable saws or dentil floss. Nah, you have all the real answers you need.

Based on their policy yes. Seems like they would be in a position to help or turn you away as needed and you would need to understand. I'm betting they would assist if asked though unless you're asking too much.