Search results

+1 that less than $300 to 350 would be nice deal, under $250 to 200 smokin' deal !! ;)

+1 that the Hitachi would be an excellent choice. Go for it.

^ ^ ^ I spy a "new" avatar !! ;) +1 that SK set is pristine . . . . what a find. Well worth the $110. Hope a GJer snags it.

Nice score OP. GJer name Royce has built some fabulous vise bases. Use Advanced Search for his Username and vise . . . you'll be amazed.

^ ^ In the words of Mick Dundee . . . now THAT's a box-end wrench !!!! :thumbup:

^ ^ ^ This. Now that we know the whole story (ie used genset that had all that pipe setup inside re-used . . . .and HVAC vendor doing the copper for high-pressure 2 psi), everything should work as it sits today. +1 to replace valve. +1 that reduction regulator needs to stay outside the...

+1 to drop the chocolate Easter bunny candy you're eating . . . . . AND . . . a Canadian GJer go snag that cool toolbox !! :thumbup: Heck for $20, you can't hardly buy a plastic toolbox like that.

+1 that GJer's absolutely NEED to know Where the OP is located to give best advice. Concrete and building practices for frost heave considerations vary with weather. Same is true for insulation, etc. UPDATE GJ Profile with a Location. Good luck.

Take a PICTURE of the marking of the wire in wall . . . . . . . do NOT assume that the wiring is correct just because it's a "new" house. GJ Sparky's will set you straight . . . . IF . . . you provide enough information. Compressors of that size are hard WIRED based on HP of the motor, that...

Did you stop him . . when he grabbed the top-handle chain saw ??? :D

Oh, I thought you just got the generator last year . . ie for first time ?? The shutoff should be near the outside of house . . BEFORE . . the other stuff going out to generator so you can isolate all that outside stuff. If something goes wrong (ie massive leak), you want quick and easy way...

Damn . . . . who installed all that mish-mash of NG pieces ?? Looks like some of those pieces of pipe are 50+ years old ???!!!! :shocking: +1 to just re-do it all from scratch. Be sure to add a Shut-Off valve just outside the house.

City just redid ALL the water down my street in last month. They pulled out the copper that went under the street to old steel supply line. Now there is 8" blue high-strength plastic main supply. The "feeder" line to my house was horizontally drilled with Ditch Witch and they used 1" blue...

^ ^ ^ You got it !! Good, it went to a GJer !! Hope it cleans up nice for you. What research I did said it was quality drill press and sought after. However, did not know what speeds it could turn for steel. Does it have middle pulley for very low speed ?? Can you post up pics of the red...

Yep, that beast is listed in thread . . . . Craigslist Finds. My BIL has 6 car garage and he's a machinist. I've alerted this find to him and who knows . . . . . Roadtrip with a big **** trailer ??? ;)

^ ^ Please post up the Details . . . Where to get FORM ? Deadline ?? Etc.

^ ^ ^ ^ This. At post # 36 with a Piggy-Back THREAD JACK similar question about 3/4" conduit. Original post from 2012 . . . . . DIG IT UP for 6 ft and Do It Right w/ 2" conduit . . . . . . . and MHF Al 2-2-2-4 for 90A. New Post # 36 - - - Have you done LOAD CALC's to justify the effort of...

Attempt at BIGGER pictures.

Ran across the Powermatic model 1150 drill press below and curious what GJer's think it might be worth . . given it's condition with rust, missing, ball on handle, etc. Also would it be a capable drill press for steel ??

How about another Pic with the markings ??